Filter
Top Products
14
Basic Remote Control Functions
INPUT
Press → Switches to external video
INPUT 1 mode.
Press again → Switches to external video
INPUT 2 mode.
Press 3 times → Switches to external video
INPUT 3 mode.
Press 4 times → Switches to external video
INPUT 4 mode.
Press 5 times → Switches to external video
INPUT 5 mode.
Press 6 times → Switches back to the
original TV mode.
POWER
Press → On.
Press again → Off. (Stand-by)
PERSONAL PREFERENCE buttons
•
Used to select any of four preset channels.
(See page 48 to setup.)
Cursor buttons
Used to move cursor on menu screen.
ENTER button
CHANNEL UP/DOWN
(+) Selects the next higher channel.
(–) Selects the next lower channel.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
(See page 17.)
AV MODE
(See page 58.)
MUTE
Press → Mutes sound.
Press again → Restores sound.
•
CLOSED CAPTION appears when sound is muted.
DIRECT CHANNEL ACCESS
Accesses any channel/inputs numbers by the keypad.
button: DTV Decoder only
ENT.
Used in some instances where a Cable
Converter Box requires an “enter”
command after selecting channels, when
using the DIRECT ACCESS button. (See
page 63.)
DISPLAY
Press →
Press again → Displays remaining time of
SLEEP TIMER and VIEW
TIMER for four seconds.
FLASHBACK
Returns to previously viewed channel.
Q-SOUND
Controls the surround settings.
(See page 29.)
VIEW MODE
Select view size. (See page 57.)
VCR/DVD/DTV CONTROL
(See pages 63 ~ 67.)
DDFC
Used to select High-quality image.
(See page 58.)
LIGHT
When this button is pressed, some buttons on the
remote control unit will light. The lighting will turn off if no
operations are performed within about six seconds. This
button is used for performing operations in dark places.
ANT-A/B button
Press to switch between ANTENNA-A and
ANTENNA-B when you wish to watch TV.
Remote control mode select buttons
Use to switch the remote control unit modes.
• By selecting one of the three mode select buttons,
this remote control can be used to adjust common
functions, such as channel selection, for that device.
INFRARED TRANSMITTER WINDOW
This remote control can be used to operate the Rear Projection TV, a VCR, a DTV STB Decoder, a DVD Video
Player and a Cable TV converter.
The buttons that can be used differ according to the device connected. Please refer to the next page for details.
Displays receiving channel for
four seconds.
Splits the screen into two smaller
equally sized screens, when pressed
again, enlarges the left screen, and,
if pressed again, exits the function.
POP FUNCTION
You can watch two pictures at the same time. (See
page 59.)
-CH- : Used to switch the channel for the
sub-picture of the TWIN PICTURE
screen.
INPUT:
Used to select the source from INPUT
terminals for the sub-picture of the
TWIN PICTURE screen.
TWIN PICTURE:
SEARCH: Press to select the SEARCH
screen mode.
SELECT: Selects the screen in TWIN
PICTURE and Search screen modes.
FREEZE: When this button is pressed with
the regular screen, will change to the
TWIN PICTURE screen and the
picture at the time the button was
pressed will become the sub-picture,
displayed as a frozen image.
SWAP: The left and right screens are
interchanged with the TWIN
PICTURE function.
CM SKIP:
Use this function when you want to
scan other channels during a
commercial break.
DTV
STB
VCR/
TV
DVD/
CATV
POWER
A
ENTER
MENU
VOL CH
AV MODE
MUTE
INPUT
ANT-A/B
DISPLAY
FLASHBACK
ENT.
DDF
C
BCD
PERSONAL PREFERENCE
Note
• The light button on the Remote Control glows in the dark. To use the glow-in-the-dark display on the remote control, place it
under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.