Filter
Top Products
– 42 –
Error messages (continued)
E-64
S REEL ROTA
TOO FAST
If the supply reel motor speed is abnormally high, the
error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-67
T REEL ROTA
TOO FAST
If the take-up reel motor speed is abnormally high,
the error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-69
T REEL
TORQUE ERR
If excess torque being applied to the take-up reel
motor is detected, the error number flashes on the
display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-70
S REEL
TORQUE ERR
If excess torque being applied to the supply reel
motor is detected or an abnormal current flowing to
the current detection resistor is detected, this error
number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-71
CAP TENSION
ERROR
If abnormal tension at the supply side is detected in
the capstan mode, the error number flashes on the
display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-72
REEL TENSION
ERROR
If abnormal tension at the supply side is detected in
the reel mode, the error number flashes on the
display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-73
REEL DIR
UNMATCH
If the take-up reel motor has rotated in the reverse
direction, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-74
DRUM TORQUE
ERROR
If excess torque being applied to the cylinder motor is
detected, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-78
M-IF COMM
ERROR
If a problem has been encountered in communication
between the servo microcomputer and mechanism
relay board, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
Monitor display Description
VTR operation
Corrective action
Note:
Consult your dealer if the error message is still displayed even after restarting the unit.
E-59
DRUM ROTA
TOO SLOW
If the cylinder motor speed is abnormally low, this
error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-60
DRUM ROTA
TOO FAST
If the cylinder motor speed is abnormally high, this
error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-61
CAP ROTA
TOO SLOW
If the capstan motor speed is abnormally low, the
error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-57
S-FF/REW
TIMEOVER
If the start or end processing operation is not
completed, this error number flashes on the display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-52
W-UP REEL
NOT ROTA
If the take-up reel fails to take up the tape while the
tape is traveling in the state where the total amount of
the tape has not yet been detected after the cassette
was inserted, this error number flashes on the
display.
Set the POWER switch
to OFF and then to ON
again.
STOP
E-55
UNLOAD ERROR
If the tape has not been taken up during unloading,
this error number flashes on the display.
Set the POWER switch to
OFF and then to ON again.
STOP
E-53
WINDUP ERROR
If there is an abnormally large discrepancy between
the amount of tape taken up by the take-up reel and
the amount of tape supplied by the supply reel while
the tape is traveling after the total amount of the tape
begins to be detected, this error number flashes on
the display.
Set the POWER switch
to OFF and then to ON
again.
STOP