Filter
Top Products
29
RQT9338
Network
In most cases, default settings can normally be used
without making any changes.
Set the IP address only when the router has no DHCP
server functions or when the router’s DHCP server
function is disabled.
After performing steps 1–3 (> 28)
4 Press [3, 4] to select “IP Address Auto-
Assignment” and press [2, 1] to select
“Off”.
≥Generally leave "On" selected.
≥When "Off" is selected, "DNS-IP Auto-Assignment"
(D below) is also automatically "Off".
5 Press [3, 4] to select “IP Address”,
“Subnet Mask” or “Gateway Address” and
press [OK].
6 Enter numbers with the numbered buttons
and press [OK].
≥If a wrong number is entered, then press [CANCEL].
7 Press [2, 1] to select “Yes” and press
[OK].
≥After checking the specifications for your broadband router,
enter each number. If the number is unknown, then check the
number of other devices such as personal computers
connected via a LAN cable. Assign a different number from
those of other devices for the “IP Address” and the same
number for others.
≥The numeric input range is between 0 and 255.
In most cases, default settings can normally be used
without making any changes.
When setting an assigned DNS server from your Internet
service provider, perform the following settings.
After performing steps 1–3 (> 28)
4 Press [3, 4] to select “DNS-IP Auto-
Assignment” and press [2, 1] to select
“Off”.
5 Press [3, 4] to select “Primary DNS” or
“Secondary DNS”and press [OK].
6 Enter numbers with the numbered buttons
and press [OK].
≥If a wrong number is entered, then press [CANCEL].
7 Press
[
2
,
1
] to select “Yes”
and press [OK].
≥Follow the instructions given by your Internet service provider
and enter the numbers.
If the number is unknown, then check the number of other
devices such as personal computers connected via a LAN
cable and assign the same number.
≥The numeric input range is between 0 and 255.
When the connection test results in “Fail” after the IP and DNS-
IP addresses are assigned, perform the following settings.
After performing steps 1–3 (> 28)
4 Press [3, 4] to select “Connection Speed
Auto-Config” and press [2, 1] to select
“Off”.
5 Press [3, 4] to select “Connection Speed
Setting” and press [2, 1] to select a
connection speed.
≥Select a connection speed in accordance with the
environment of the network connected.
≥When the settings are changed, the network connection may
be slower or disabled depending on the device.
Always test the connection when new “Proxy Server Settings”
have been made.
1 Press [SETUP].
2 Press [3, 4] to select “Network Settings”
and press [OK].
3 Press [3, 4] to select “Proxy Server
Settings” and press [OK].
4 Press [3, 4] to select “Connection Test”
and press [OK].
“Testing”: The test is in progress.
“Pass”: The connection is completed.
Press [RETURN] to exit.
“Fail”: Please check the connection and settings.
In most cases, default settings can normally be used
without making any changes.
Please use this setting when instructed to by your Internet
service provider.
After performing steps 1–3 (D above)
4 Press [3, 4] to select “Proxy Address”
and press [OK].
(Continued on the next page)
Setting the IP address
Setting the DNS-IP
192
.
.
.
1
Primary DNS
Please input Primary DNS and press
[OK]. Press [CANCEL] to delete the selected
character. To clear this setting, delete all
characters and press [OK].
Num
ber
0
-
9
Setting the connection speed
Testing of “Proxy Server Settings”
Setting the proxy server
RETURN
Proxy Server Settings
Initialize
Proxy Address
Proxy Port Number
OK
0
Connection Test
----
DMPB15EB-RQT9338_eng.book 29 ページ ２００９年３月２７日 金曜日 午後１０時１３分