Filter
Top Products
13
PHILIPS LTC3963/61 (E) QR31808
SETUP
On-Screen displays are provided to aid setup of the
programmable functions. The six functions on the
Program Menu appear individually on the monitor
in this order.
1. CLOCK SET
2. TIMER
3. SELECTION MENU 1
4. SELECTION MENU 2
5. ALARM
6. ALARM MEMORY
CLOCK SET
TIMER DISPLAY
SELECTION MENU 1
Initial Program Function Display Formats
M
ON:
✽✽
06
❲
1
❳
2
2
2
2
2
2
2
1
1
1
1
1
1
1
:00
a
06
❲
2
❳
:00
a
06
❲
3
❳
:00
a
06
❲
4
❳
:00
a
06
❲
5
❳
:00
a
06
❲
6
❳
:00
a
06
❲
7
❳
,
THU:
✽✽
,
TUE:
✽✽
,
FRI :
✽✽
,
SUN:
✽✽
,
W
ED:
✽✽
,
SAT:
✽✽
,
:00
A
A
A
A
A
A
A
2
2
2
2
2
2
2
1
1
1
1
1
1
1
:00
:00
:00
:00
:00
:00
:00
A
A
A
A
A
A
A
a
ELE
O
CT
SE EEADPCH S
X5
M
S
R:
SE
I
ON H T
6F
BA :EUT
LED
RA
96
D00BAUD
ERC:
W
R
M
:E
L
CA A S
AL
ENUION
❲❳
SELECTION MENU 2
ALARM DISPLAY
ALARM MEMORY DISPLAY
DU
L
R
AR
M
:TION U
M
AL
AN
S
SPE D:
06
A
LAR
M
A
LAR
M
A
LAR
M
A
A
RE SIND,
W
DU
FU
RTION
ION
A
E
YDR:AE
:OTU
YE
SET
❲❳
TOP
NC
IF
TCLECYRE
❲
S
❳
LAR
MMM
1
A00A
2
3
4
5
6
7
8
9
ORYE
❲❳
1–
:
1–19 FRI990
0: A021
LOCKCSET
❲❳
TYPO:E
ADJ :US SLAVETTI
M
E
OFFSD
PTIOONS
❲❳
ELECT
EN
E
SEL
TA NEP
T
D
OF
M
S
E
O
:
TR UOBL
F
F
OFF
OFF
:
ZBUZ E
O
I
CRT
I:VNEODO
E:RAU C CHECK
OF
ENUION
❲❳
F
LAR
M
A
O:TU
OF
Note: If the VCR is not turned on for about 720
hours after the built-in battery is fully charged (after
the VCR is turned on for more than 48 hours), the
TIME/DATE display will be cleared.
SELECTING A FUNCTION TO BE PROGRAMMED
The program menu will always begin with the
CLOCK SET function, followed by the TIMER,
SELECTION MENU 1, SELECTION MENU 2,
ALARM, and then the ALARM MEMORY functions.
Although the program menu always follows this
order, it is possible to skip any of the available func-
tions during the selection process.
To select the desired program function (and to move
from one program function to the next), press the
PROGRAM button repeatedly until the desired func-
tion display format appears on the monitor.
After the desired function has been selected, follow
the corresponding procedure to set that function.
SETTING THE PROGRAM FUNCTION(S)
The first step in each programming procedure is:
“Press the START/STOP button”. The system
allows up to five minutes for any one function set-
ting to be completed after the START/STOP button
is pushed. If no change/setting is entered within the
five minutes period, the unit will automatically exit
the selected program function. (If this happens, re-
select the desired program function, and follow the
programming procedure for that function.)
The following procedures for setting VCR functions
assume that the desired function has already been
selected.
Note: During programming, holding the SET, UP, or
DOWN button will move/change the displayed infor-
mation at a rapid rate.