Filter
Top Products
|
24 English
Settings
Reset
Reverts all settings to their defaults
except for the network and Smart
Hub settings, and then starts the
Setup function. Requires that you
enter your security PIN. The default
security PIN is 0000
Networks and the Internet
When you connect this product to a network, you can
use network based applications and functions such as
Smart Hub and BD-LIVE, and upgrade the product's
software through the network connection. For more
information about accessing and using Internet services,
see the Network Services chapter of this manual on
pages 41~49. Instructions for configuring the network
connection start below.
Configuring Your Network Connection
If you didn't configure your network connection during the
initial settings procedure or you need to reset the network
connection, follow the directions below.
Before you begin, contact your Internet Service Provider
to find out if your IP address is static or dynamic. If it
is dynamic, and you have a wired or wireless network,
we recommend using the Automatic configuration
procedures described below.
If you are connecting to a wired network, connect the
product to your router using a LAN cable before you start
the configuration procedure.
To begin configuring your network connection, follow
these steps:
1. In the Home screen, select Settings, and then
press the
E
button.
2. Select Network, and then press the
E
button.
3. Select Network Settings, and then press the
E
button.
4. Go to the instructions for Wired networks starting
below or the instructions for Wireless networks
starting on page 25.
Wired Network
❑
Wired – Automatic
After following Steps 1 to 3 above:
1. In the Network Settings screen, change Network
type to Wired. Then, select Connect and press
the
E
button. The product detects the wired
connection, verifies the network connection and
then connects to the network.
2. When it is done, highlight OK, and then press
E
button.
❑
Wired - Manual
If you have a static IP address or the automatic procedure
does not work, you'll need to set the Network Settings
values manually.
After following Steps 1 to 3 above:
1. In the Network Settings screen, change Network
type to Wired. Then, select Connect and press the
E
button.
The product searches for a network, and then
displays the connection failed message.
| NOTES |
\
If it is possible to connect the home theater to your
network wirelessly, select Change Network at this
point, change the Network Type to Wireless, and
then go to the instructions for wireless networks on
page 25.
Network Settings
Wired network connection failed.
MAC Address XX:XX:XX:XX:XX:XX
IP Address 0. 0. 0. 0
Subnet Mask 0. 0. 0. 0
Gateway 0. 0. 0. 0
DNS Server 0. 0. 0. 0
Unable to connect to the network. Try the following: check if your IP address is
set correctly in IP Settings. Contact your Internet Service Provider for more
information.
IP SettingsChange Network Retry Close
2. Use the ◄► buttons to select IP Settings, and
then press the
E
button. The IP Settings screen
appears.
3. Select the IP Setting field, and then set it to Enter
manually.
4. Select a value to enter (IP Address, for example),
and then press
E
. Use the number keypad on
your remote control to enter the numbers for the
value. You can also enter numbers using the ▲▼
buttons. Use the ◄► buttons on the remote control
to move from entry field to entry field within a value.
When done with one value, press the
E
button.
5. Press the ▲ or ▼ button to move to another value,
and then enter the numbers for that value following
the instructions in Step 4.
6. Repeat Steps 4 and 5 until you have filled in all
values.
| NOTES |
\
You can get the Network values from your Internet
provider.
7. When finished entering all the values, select OK,
and then press the
E
button. The home theater
verifies the network connection and then connects
to the network.