Sanyo SRC-850 VCR User Manual


 
AUTOREPEAT RECORDING
Autorepeat Recording
The same tape can be recorded over many times.
Follow the Before starting steps, under “NORMAL
RECORDING”.
1 Press the MENU button until the (SET UP 2) menu is
displayed.
@@@@@@@<SET@UP@2>
öDISPLAY
@@@DATE@@@@@@@@@@Y
@@@TIME@@@@@@@@@@Y
@@@ALARM@COUNT@@@Y
öTAPE@IN@MODE@@@@STOP
öTAPE@END@MODE@@@REW
öOUTPUT@@@@@@@@@@SERIES
öSERIES@REC@IN@@@N
öEJECT@MODE@@@@@@EJECT1
öTHREAD@CHECK@@@@Y
2 Press the ] button, until the “TAPE END MODE” (or
“REPEAT”) setting is flashing.
3 Press the l (or j) button, to set to “R1” or “R2”. (See
“Setting the Mode at the End of the Tape”)
4 Press the PAUSE/SEARCH button to save the
setting.
5 Press the REC button.
°
Recording will start. When the tape end is
reached, the VCR will rewind it to the beginning,
and recording will resume.
°
When the end of the tape is reached, a buzzer
will be heard (if in the (SETUP 3) menu, in the
BUZZER section TAPE END is set to “Y”) and
“OFF” will be displayed until the rewinding
operation starts.
NOTES:
If during autorepeat recording there is an alarm trigger,
“AL” is displayed on the digital display and alarm
recording will take place. (Please refer to page 15,
“ALARM RECORDING”.)
If the “TAPE END MODE” setting is R1 and there is an
alarm trigger, the recording will continue to the end of
the tape then it will be rewound to the beginning and
stop. “OFF” will be displayed on the digital display. To
turn off the buzzer (if in the (SETUP 3) menu, in the
BUZZER section TAPE END is set to “Y”) and the
“OFF” display, press the EJECT, PLAY, FF or REW
button.
If “AL” is displayed on the digital display and the “TAPE
END MODE” setting is R1, autorepeat recording is not
possible.
Setting the Mode at the End of the Tape
In the (SET UP 2) menu, you can set the mode of the
VCR mode when the tape reaches the end during
recording.
1 Press the MENU button until the (SET UP 2) menu is
displayed.
@@@@@@@<SET@UP@2>
öDISPLAY
@@@DATE@@@@@@@@@@Y
@@@TIME@@@@@@@@@@Y
@@@ALARM@COUNT@@@Y
öTAPE@IN@MODE@@@@STOP
öTAPE@END@MODE@@@REW
öOUTPUT@@@@@@@@@@SERIES
öSERIES@REC@IN@@@N
öEJECT@MODE@@@@@@EJECT1
öTHREAD@CHECK@@@@Y
2 Press the ] button, until the “TAPE END MODE” (or
“REPEAT”) setting is flashing.
NOTE:
If “TAPE END MODE” is set to “R1” or “R2” (see
step 3), “REPEAT” will be indicated intead of
“TAPE END MODE”.
3 Press the l (or j) button, to set the desired mode.
REW. . . . . . . . Rewinds the tape to the
beginning, then goes to stop mode
STOP . . . . . . . Goes to stop mode
R1. . . . . . . . . . Autorepeat recording mode is
automatically canceled if there
was an alarm trigger
R2. . . . . . . . . . Autorepeat recording mode is
active even if there was an alarm
trigger
4 Press the PAUSE/SEARCH button to save the
setting.
NU4Q/U3 (SRC-850 GB) Mon. Aug., 23/1999
14
English