Filter
Top Products
— 32 —
KV-27S40 / 27S45 / 27S65 / 29SL40 / 29SL40A / 29SL40C/
29SL45 / 29SL65 / 29SL65C/ 29XL40M / 29XL40P / 29XT11A
6. Connect an oscilloscope probe to C Board, CN301 Pin 5
(RED OUT).
7. Select RDRV with
and .
8. Adjust with and for: 1.90 ± 0.05 Vp-p.
9. Reset the item DCOL to "1" level.
10. Write the memory by pressing
then .
11. Return the following back to normal after adjustment.
PICTURE . . . . . . . . . . . MAX
COLOR . . . . . . . . . . . CENTER
BRIGHT . . . . . . . . . . . CENTER
R ON . . . . . . . . . . . ON (1)
G ON . . . . . . . . . . . ON (1)
B ON . . . . . . . . . . . ON (1)
(5) Feature ID Map
5-2. A BOARD ADJUSTMENTS
H. FREQUENCY ADJUSTMENT
1. Input a monoscope signal.
2. Set to Service adjustment Mode.
3. Connect a frequency counter to base of Q501
(TP-500 H. DRIVE).
4. Select the item of AFC, set to 3 level (free run).
5. Check H. Frequency for the 15735 ± 200 Hz. (NTSC) or
check H. Frequency for the 15650 ± 200 Hz. (Trinorma)
6. Select the item of AFC again, adjust the level "0".
7. Write into the memory by pressing
then .
V. FREQUENCY ADJUSTMENT
1. Select video 1 with no signal input.
2. Set the conditions with standard setting.
3. Connect the frequency counter across TP-508 or CN501
VDY (+) pin 6 connector and ground.
4. Check V. Frequency for the 60 ± 2 Hz (NTSC)
5. Check V. Frequency for the 50 ± 2 Hz (Trinorma).
SUB CONTRACT ADJUSTMENT (SCON)
1. Input a color-bar signal.
2. Select the red color.
3. Set to Service adjustment Mode.
4. Select the item DCOL to "0" level.
5. Set the conditions as follows.
PICTURE . . . . . . . . . . . MAX
COLOR . . . . . . . . . . . MIN
BRIGHT . . . . . . . . . . . CENTER
R ON . . . . . . . . . . . ON (1)
G ON . . . . . . . . . . . OFF (0)
B ON . . . . . . . . . . . OFF (0)
White
n
n
Black
1.8 ± 0.05 Vp-p
1.90 ± 0.05 Vp-p
1: ON
0: OFF
SERVICE RON 1
KV-
DESTINATION
ID-0
ID-1
ID-2
ID-3
ID-4
ID-5
ID-6
ID-7
1 27S40 (US) 153 1 13 195 31 1 0 64
2 27S40 (CND) 129 1 13 195 31 1 0 64
3 27S45 (US) 153 27 13 195 31 1 1 64
4 27S45 (CND) 129 27 13 195 31 1 1 64
5 27S65 (US) 153 27 15 195 31 1 7 64
6 27S65 (CND) 129 27 15 195 31 1 7 64
7 29SL40 (E) 145 1 141 195 63 1 0 64
8 29SL40A (E) 151 1 141 195 55 1 0 64
9 29SL40C (E) 145 1 141 195 63 1 0 64
10 29SL45 (E) 145 27 141 195 63 1 1 64
11 29SL65 (E) 145 27 143 195 63 1 7 64
12 29SL65C (E) 145 19 143 195 63 1 7 64
13 29XL40M (MX) 145 1 141 195 63 1 0 64
14 29XL40P (E) 145 1 141 195 63 1 0 64
15 29XT11A (E) 151 1 141 195 55 1 0 64