Filter
Top Products
22
Chapter 2: Connecting your TV
(E) 46/52/62HM95
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
Connecting IEEE1394 video devices
You can use the two bi-directional IEEE1394 ports on the back
of your TV to connect digital video devices that meet CEA
specifications for IEEE1394.
Because these ports are bi-directional, they can be used for both
playback and recording.
• Because IEEE1394 is an evolving technology, it is possible that some
or all of the connectivity features of a device you connect to the TV
through the IEEE1394 ports may not operate. You should confirm
that the devices you want to use with the IEEE1394 ports will operate
with those ports.
• This TV does not support all possible IEEE1394 signal types. For
information on signals supported by the IEEE1394 ports, see
“Supported signals” at right.
• IEEE1394 cable carries both audio and video information;
separate audio cables are not required.
You will need:
one (or two) IEEE1394 cables
Note: The transmission capability of IEEE1394 cable used with this
TV must be S400 (400 Mbps maximum).
additional A/V cables if your device is analog-compatible
(see “Using analog-compatible IEEE1394 devices” below).
Two bi-directional
IEEE1394 ports
Using analog-compatible IEEE1394
devices
Some digital IEEE1394 devices are compatible with analog
signals. For example, some D-VHS VCRs can record and play
VHS or S-VHS format videos. Such devices allow you to play
analog tapes that you rented or recorded, or record analog
programs from antenna or Cable TV systems. To use the
IEEE1394 device’s analog features, you need to connect the
device to the TV using standard A/V cables (or S-video plus
audio cables) in addition to connecting the IEEE1394 cable.
Note: If you have an IEEE1394 device connected to both digital
and analog inputs on the TV, the TV automatically switches
between digital and analog modes, as needed, when the initial
device access is initiated using the TheaterNet button.
See page 45 for details on using the TheaterNet feature.
Supported signals
The IEEE1394 ports support only the signals listed below. Even
though incompatible video, audio, and digital control signals
cannot be decoded by the TV, these signals may be passed
through the IEEE1394 cable to other compatible devices.
Incompatible devices may not appear in the TheaterNet
™
menu.
• MPEG-2 digital video signals
Other digital video signals—such as DV video—are
incompatible and must be decoded by the source device and
sent to the TV as analog video (composite or S-video).
• Dolby Digital and MPEG digital audio signals
Other digital audio signals (such as DPM, MP3, and DTS) are
incompatible and cannot be decoded by the TV.
• EIA-775 and AV/C digital control
Your TV can serve as the control center for many devices
that are compatible with EIA-775 or AV/C IEEE1394
control standards (described below).
The TV cannot control IEEE1394 devices that use any other
control standards.
– EIA-775 digital control allows tuning devices (such as
Cable boxes) to send simple graphics; however, this
standard does not allow the TV to control the Cable box
through IEEE1394.
– AV/C (audio/video control) provides basic control (such
as power, play, stop rewind, fast-forward, pause, and
record), as applicable to the specific device.
Using TheaterNet
™
on-screen device
control
You can use the TheaterNet feature to control some IEEE1394
devices using on-screen control icons. See page 45 for details on
setting up and using the TheaterNet feature.
Note: If the TheaterNet feature does not control your
IEEE1394 device, you can either use the device’s remote
control or try using IR pass-through with the TV’s remote
control (page 21).
TV back panel
NOTE: NEVER CONNECT THIS TV
TO A PERSONAL COMPUTER (PC).
THIS TV IS NOT INTENDED FOR USE WITH A PC.
From IEEE1394
devices (such as
AVHD or D-VHS)
}
HM95_R1_012-25_061505 6/24/05, 9:13 PM22