Filter
Top Products
54-EN
01GB06IVA-W502E.fm
ALPINE IVA-W502E 68-12118Z56-A (EN)
Operating Auxiliary Devices (Optional)
To operate your devices connected to the AUX terminals on the rear
panel of IVA-W502E (AUX mode) or to the iPod Direct connector by
using iPod Direct/RCA Interface cable (sold separately) (AUX+ mode),
follow the procedure described below.
•
If you try to activate the auxiliary device while driving, the display will
show the warning-PICTURE OFF FOR YOUR SAFETY.
1
Touch [SOURCE] on the main source screen.
The source screen appears on the display.
2
Touch [AUX]*
1
or [AUX+]*
2
.
The external input screen is displayed.
3
Touch [NTSC/PAL] to change the video input.
4
Touch [COMP. /S-VIDEO]*
3
to switch the video
signal input mode.
The mode switches with each touch.
*
1
The name which is given as the source name in “Setting the AUX
Mode” on page 36 is displayed.
*
2
The mode which is given as the source name in “Setting the AUX+
Mode” (page 37).
*
3
The video signal can be input in two ways, selecting the right mode
depending on the connection method. Switching to the COMP. mode
when using the Video Input Connector. Switching to the S-VIDEO
mode when using the S Video Input Connector.
• If the AUX mode is not displayed on the main menu, set AUX IN to
ON by following “Setting the AUX Mode” (page 36).
• The setting of switching NTSC/PAL, which you have set in this
section can be used in same way in “Switching the Visual Input
Signal System” on page 36.
• The display mode changes by touching [WIDE].
For operation, refer to “Switching Display Modes” on page 26.
• After connecting the KCA-410C, its AUX input can be used only in
INTERRUPT MODE. For details, refer to the KCA-410C Owner’s
Manual.
Operating the TUE-T200DVB (Optional)
Operable when optional TUE-T200DVB is connected.
When DVB-T is selected in “Setting the AUX Mode” (page 36), the
source is displayed in SOURCE selection screen.
1
While your vehicle is parked, touch [SOURCE] on
the main source screen.
The source screen appears on the display.
2
Touch [DVB-T].
The DVB-T screen is displayed.
3
Perform the desired operation.
Channel Number Up/Down or favourite Channel Number
Up/Down
Touch [CH.]* to select changing the Channel or the
favourite Channel.
Touch CH. [ ] or [ ] to move the Channel number Up/
Down.
Touch FAV [ ] or [ ] to move the favourite Channel
number Up/Down.
* The button displays the current changing mode ([CH.] or [FAV]).
Calling up Main Menu Screen
Touch [MENU] to call up the main menu screen.
Calling up Menu Operation Mode
1
Touch [P1/2].
The function guide appears.
2
Touch [MENU CONT] to call up the menu operation
mode.
Switching the Source
Touch [BAND].
The source switches with each touch.
Calling up Electronic Programme Guide (EPG)
Touch [EPG] to call up the Electronic Programme
Guide.
Scanning Mode
1
Touch [P1/2].
The function guide appears.
2
Touch [A.MEMO] to start the auto scan procedure.
• For detail, refer to the Owner’s Manual of the TUE-T200DVB sold
separately.
Switching the Video Input Mode
Touch [COMP./S-VIDEO].
The video signal input mode switches with each touch.
• Switching to the COMP. mode when using the Video Input Connector.
Switching to the S-VIDEO mode when using the S Video Input
Connector.
Auxiliary Device
(Optional)
WARNING
It is dangerous (and illegal in many states) for the
driver to watch the TV/Video while driving the vehicle.
The driver may be distracted from looking ahead and
an accident could occur.
Install the IVA-W502E correctly so that the driver
cannot watch TV/Video unless the vehicle is stopped
and the emergency brake is applied.
If the IVA-W502E is not installed correctly, the driver
will be able to watch the TV/Video while driving the
vehicle and may be distracted from looking ahead and
cause an accident. The driver or other people could
be severely injured.
TUE-T200DVB
Operation (Optional)
01GB00IVA-W502E.book Page 54 Wednesday, February 20, 2008 4:12 PM