Filter
Top Products
24 EN
INITIAL SETTING (cont.)
E Enter cable box brand
F Engage test mode
Press [FG] to move the arrow to “TEST MODE”,
then press [OK].
NOTE:
If you do not engage the test mode in step F, “INPUT
CH” and “BRAND” are not set.
•If the cable box’s channel does not change to 9
A Press [D E] to move the arrow to “NO”.
B Press [OK].
C Repeat step
E until the cable box’s channel
changes to 9 by entering another code.
D If the channel does not change after going
through all the code numbers listed for your
model of cable box, then try all the other
numbers.
G Return to normal screen
Press [MENU].
CABLE BOX BRAND LIST
NOTES:
• The Controller may not work with all types of cable box.
• If your cable box does not respond to any code, you cannot
use the Controller to change cable box channels. In this case,
make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled start time of timer
recording.
Contact your cable company about the possibility of
exchanging your current cable box with the one compatible
with your VCR.
• The VCR can only change the cable box channel through the
Controller during timer recording.
• If your cable box cannot be operated with a Remote (because
it has no remote sensor), you cannot use the Controller to
change its channels. Make sure to leave the cable box turned
on and tuned to the proper channel before the scheduled start
time of timer recording.
• If the VCR’s memory backup expires because of a power
failure, set the cable box input channel and brand again.
• For customers in U.S.A.: If you are unable to set the
Controller, contact JVC toll free at 1-800-252-5722.
End of Cable Box Control Setting
Press [FG] to move
the arrow to
“BRAND”.
Press [D E] to enter
the brand code from
the list shown to the
right.
•If the cable box’s
channel changes to
9, setting is
complete
Press [D E] to
move the arrow to
“YES”, then press
[OK] and “CABLE
BOX CONTROL IS
ON” appears on the
screen for about 5
seconds.
If the VCR’s clock has not been set (with “AUTO
CLOCK” set to “ON”)
“CABLE BOX USERS SET CLOCK MANUALLY”
appears for about 5 seconds when you press [OK] in
step
C, then the Clock Set screen appears.
Perform Manual Clock Set on page 19. If you press
[MENU] after the clock has been set, the Cable Box
Input Channel screen in step
D appears.
FUNCTION SET UP
INITIAL SET UPTUNER SET UP
THEN PRESS [OK]
INPUT CH
BRAND 1
TEST MODE
OFF
SELECT WITH ARROW KEYS
SELECT
OK
EXIT
MENU
CABLE SET UP
INPUT CH
BRAND 1
TEST MODE
OFF
FUNCTION SET UP
INITIAL SET UPTUNER SET UP
THEN PRESS [OK]
SELECT WITH ARROW KEYS
SELECT
OK
EXIT
MENU
CABLE SET UP
YES NO
DID YOUR CABLE BOX CHANGE TO
CHANNEL 09?
BRAND CODE
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
1, 17
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15, 28
10, 18, 23
15
1, 4, 6, 11, 12, 15, 28
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
T1, 16, 17
5, 16, 24
2, 8
7, 20
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
1, 4, 16
1, 17
16, 17, 25
3, 9, 22
3, 9, 22