Filter
Top Products
5
2 YOUR FIRST QSO (HF/ 50 MHz band)
TRANSMITTING
PF
F LOCK
A
1
C
H
1/R
E
C
2
C
H
2
/R
E
C
3
C
H
3/R
EC
4
T
O
N
E
/S
E
L
5
M
E
TE
R
6
C
TC
S
S/S
EL
7
N
B/LEV
E
L
8
A
G
C
/O
FF
9
F
IN
E
/S
TE
P
.
D
C
S
/S
E
L
0
S
H
IF
T
/O
F
F
S
E
T
E
N
T
SEND
PHONES
MIC
AT
ANT1/2
PROC
LEVEL
VOX
ATT
PRE
LEVEL
LEVEL
LEVEL
MANUAL
LO/
WIDTH
HI/
SHIFT
N.R.
A.N.
B.C.
F
U
N
C
CALL
C.IN
CLR
MAIN
AUTO
CAR
TX MONI
DELAY
NAR
REV
MIC
PWR
KEY
LSB
USB
CW
FSK
FM
AM
SUB
DISP
SEL
1MHz
CTRL
MR
MG.SEL
M.IN
QUICK MEMO
M
/S
RE
V
TRACE
M
AIN
M
AN
U
A
L
R
F
AF
SQ
L
S
U
B
C
H
MULTI
B
C
M
A
IN
G
AIN
VFO/CH
MENU
TF-
SET
MAIN SUB
SG.SEL
SCAN
M VFO
M.IN
RIT
CW TUNE
9.6k STA
RIT/SUB
CON
XIT
ALT
SET
CLEAR
P. C . T
_
+
HF/VHF/UHF ALL MODE MULTI BANDER TS-2000
S
A
T
L
A
/B
VFO/M
SPLIT
A=B
4 9
71
85
32
q Turn the Tuning control to tune in a desired
station or to select an unused frequency.
w Press [AT/ ANT1/2] momentarily.
•“AT” appears.
F
I
L
T
E
R
S
1
3
5
7
9
2
0
4
0
6
0
d
B
P
W
R
1
0
2
5
5
0
1
0
0
W
A
L
C
e Press and hold [AT/ ANT1/2] to activate the built-
in antenna tuner.
•“AT” starts blinking and the MAIN band LED
above the [MIC/ CAR] key turns red.
F
I
L
T
E
R
S
1
3
5
7
9
2
0
4
0
6
0
d
B
P
W
R
1
0
2
5
5
0
1
0
0
W
A
L
C
• Tuning should be completed in under
20 seconds, then “AT ” stops blinking.
• If tuning is not completed within 20 seconds,
error beeps sound. Press [AT/ ANT1/2] to stop
the error beeps and quit tuning. Check your
antenna system before continuing. If you do
not press [AT/ ANT1/2], tuning will continue for
approximately 60 seconds.
Note: You will hear a lot of clicking sounds coming from the
transceiver while the antenna tuner is trying to tune the antenna.
This is simply the relay switches turning ON and OFF.
r With LSB, USB, or AM selected, press
[MIC/ CAR] to activate the Microphone Gain
Adjust.
• “MIC GAIN 50” appears.
• With FM selected, skip this step.
t Press [SEND].
• The MAIN band LED turns red.
y Begin speaking into the microphone in your
normal tone of voice.
u LSB/ USB: While speaking into the microphone,
adjust the MULTI/ CH control so that the ALC
meter reflects according to your voice level.
P
W
R
1
0
2
5
5
0
1
0
0
W
F
I
L
T
E
R
S
1
3
5
7
9
2
0
4
0
6
0
d
B
A
L
C
AM: While speaking into the microphone, adjust
the MULTI/ CH control so that the calibrated
power meter slightly reflects to your voice level.
FM: Skip this step.
i When you finish speaking, press [SEND] to return
to receive mode.
o Press [MIC/ CAR] to quit the Microphone Gain
Adjustment.
Note: If desired, access Menu No. 41 {page 28} to try the
Microphone Gain Adjust for FM.
This completes your introduction to the
TS-2000(X), but there is a great deal more to know.
“OPERATING BASICS” {page 18} and the following
chapters explain all the functions of this transceiver,
starting with the most basic, commonly-used
functions.