Filter
Top Products
23
206-4207
012 - IR BANKS EN (IR Banks Enable)
For direct access to a particular channel bank. When enabled, you
can access a channel bank by inputting the discrete IR code for
that bank.
Note: This item is not available in the Installer Menu when item
027 HOSPITAL MODE is set to 0.
013 - SCAN MODE (Functional after 2-5-5 + MENU transfer of
Channel Map)
When set to 1 (default), allows TV to be turned ON when Channel
Up/Down buttons are pressed on pillow speaker. Also, TV will turn
OFF when Channel Up/Down key is used to tune above or below
Channel Map pivot point. By default, Channel Map pivot point is
between the highest and lowest channel in the Channel Map (also
see item 014 STRT CH IN SM). Set to 0 to disable.
014 - STRT CH IN SM (Start Channel in Scan Mode)
Only valid when item 013 SCAN MODE is set to 1 (enabled).
When set to 1, forces Channel Map pivot point to be between the
RF channel designated in item 004 STRT CHANNEL and next
lower channel in the Channel Map. Set to 0 to disable (default).
Note: This item is not available in the Installer Menu when item
013 SCAN MODE is set to 0.
015 - SLEEP TIMER
If set to 1, the Sleep Timer feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, the Timer function is available to the end user and
enabled continuously. Set to 0 to disable On/Off timers.
Note: Clock must be set in order for timers to be used.
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, the Alarm function is available to the end
user. Set to 0 to disable the Alarm function.
Note: Clock must be set before the Alarm function will work.
020 - FEATURE LEVEL
This function determines an additional IR code scheme to which
the TV will respond, allowing for the use of unique IR codes
based on “bed number” in a multi-TV single room installation. First
determine the IR mode; then select the bed number.
Note: Item 027 HOSPITAL MODE must be set to 0 to enable
Legacy Zenith Bed 1 or Bed 2 IR codes and Speaker selections.
Values IR Mode Bed # Speaker
0 – 1 Legacy Zenith (Hospital) 1 – 2 TV
16 – 24 Multi-code Remote 1 – 9 TV
64 – 65 Legacy Zenith (Hospital) 1 – 2 Pillow
Note: For further information, see documentation for the accessory
package that includes the multi-code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to lter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
Note: This item is not available in the Installer Menu unless item
084 PERMANENT BLK is set to 0.
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1
to use the caption setting congured before the TV was turned
OFF when the TV is turned ON.
025 - FUNCTION PRE (Function Preview)
Set to 1 to allow access to the Channel Preview/Banks Setup
Menu via the CH PREVIEW key on Installer Remote. Set to 0 to
disable access to the Channel Preview/Banks Setup Menu.
027 - HOSPITAL MODE
Set according to the speaker selection, the pillow speaker code/
supply voltage and the hospital IR code.
Value Speaker
Pillow Speaker
Code/Voltage
Hospital IR Code
000 Determined by
item 020 setting
Zenith (+12v) Disabled
001 Pillow Only Zenith (+12v) Zenith Bed #1
002 Pillow Only Zenith (+12v) Zenith Bed #2
017 Pillow Only Philips (+5v) Zenith Bed #1
018 Pillow Only Philips (+5v) Zenith Bed #2
033 Pillow Only RCA (-5v) Zenith Bed #1
034 Pillow Only RCA (-5v) Zenith Bed #2
065 TV Only Zenith (+12v) Zenith Bed #1
066 TV Only Zenith (+12v) Zenith Bed #2
081 TV Only Philips (+5v) Zenith Bed #1
082 TV Only Philips (+5v) Zenith Bed #2
097 TV Only RCA (-5v) Zenith Bed #1
098 TV Only RCA (-5v) Zenith Bed #2
129 Pillow & TV Zenith (+12v) Zenith Bed #1
130 Pillow & TV Zenith (+12v) Zenith Bed #2
145 Pillow & TV Philips (+5v) Zenith Bed #1
146 Pillow & TV Philips (+5v) Zenith Bed #2
161 Pillow & TV RCA (-5v) Zenith Bed #1
162 Pillow & TV RCA (-5v) Zenith Bed #2
254 TV Only 0v Zenith Bed #2
When Hospital Mode is enabled, channel banks are also avail-
able. Refer to channel banks information in this document for
further details. Channel banks are not supported if Hospital Mode
is set to 0 or on TVs that are congured for FTG Mode operation.
Installer Menu (Cont.)