Filter
Top Products
EN 35
4
Input receiving channel number
The guide channel
number, which is
assigned to the TV or
cable station for the
PlusCode number
that you entered in
step 3, will appear
automatically on the
Guide Channel Set Up screen.
Press
@
#
to input the number of the channel on
which the broadcast for the PlusCode number is
received on the VCR or cable box, then press
OK.
● The Guide Channel Set screen appears only
when you input the PlusCode number of a
station for which the guide channel number has
not been set previously.
● If you receive your channels with a cable box
and if you have properly set your Controller,
“CABLE CH” appears in place of “VCR CH”. If
not, refer to pages 15 – 17.
In that case, it is possible to change the channel
by 10 channels by pressing and holding
@
#
.
5
Check program data
The PlusCode
number you entered
and the
corresponding timer
recording program is
displayed on the
Program screen.
Check to make sure it
is accurate.
● To change the start/stop time, date or channel
setting, press the corresponding buttons to
change the settings; START +/–, STOP +/–,
DATE +/–, TV/VCR CH +/–.
● To timer-record daily or weekly serials, press
DAILY (number “8”) or WEEKLY (number “9”).
“MON – FRI”, “MON – SAT”, “SUN – SAT” or
“EVERY _ _ _” appears on the Program screen.
Pressing the button again makes each
corresponding display disappear.
● For the “SOURCE” setting, refer to page 39.
● If you made a mistake, press BACK to access
the VCR Plus+ screen again and input the
correct PlusCode number.
6
Set recording speed
Press REC SPEED to set the recording speed.
IMPORTANT
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong
VCR CH or CABLE CH number will be displayed on the
Program screen in step 5. When this happens, set the
correct guide channel number for that station. (੬ pg. 36,
“Changing VCR Plus+ Setting”)
NOTES:
●
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time is lost if it lasts for more
than 10 minutes.
As a result, when the power is supplied again to this VCR
after the power failure, the following will take place.
1. This VCR starts Auto Clock Set automatically to restore the
clock time.
2. If the clock time is restored correctly and “AUTO TIMER” is
set to “ON”, each timer program you have made will start
at its start time unless its end time has elapsed.
●
If the tape reaches its end during timer recording, “
‰
”, “ ”,
and “
#
” blink.
●
To timer-record cable channels received through a cable box,
be sure to keep the cable box turned on.
7
Return to normal screen
Press
@
#
to move the arrow to “CONFIRM”,
then press OK.
“PROGRAM COMPLETED PRESS [TIMER] TO
ENTER TIMER STANDBY MODE” appears on the
screen, then press OK to return to normal screen.
8
Engage timer recording standby mode
Press TIMER (‰).
The VCR turns off automatically and “‰” is
displayed on the front display panel.
To use the VCR while it is in timer recording standby
mode
Press TIMER (‰) to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
DO NOT forget to put the VCR into timer recording standby
mode again by pressing TIMER (‰) after you use the VCR;
otherwise, you cannot record the broadcasts you want.
● When “AUTO TIMER” (੬ pg. 57) is set to “ON”, the
timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have
to press TIMER (‰) to engage or disengage the timer
recording standby mode.
THEN PRESS [OK]
GUIDE CH 12
VCR CH
– –
SELECT WITH ARROW KEYS
SELECT
OK
EXIT
MENU
FUNCTION SET UP
INITIAL SET UPTUNER SET UP
CLOCK SET GUIDE CHANNEL
OTHER
CONFIRM CANCEL
10:00 PM
STD (SP)
12/24/03 (WED) 12 CH
CATVEVERY WED
8:00 PM
START TIME
PLUSCODE NO.
12345
STOP TIME DATE
REC SPEED DAILY/WEEKLY
CH
SOURCE
SET PROGRAM WITH [+/–, REC SPEED,
8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM"
START STOPDATE CH
EXIT
PROG.
TIMER PROGRAM
MV8300_U1B-EN34-41 4/1/3, 2:35 PM35