Filter
Top Products
42 EN
Navigation
Playback
This function is useful when you want to quickly find
programs you have recorded on a tape using this VCR.
This function allows you to select a program to watch,
and then automatically search for the beginning of the
program.
1
Load a cassette
Insert a tape recorded on this VCR.
● The VCR turns on automatically.
● The tape will run for a few seconds while the
VCR searches for the tape number recorded. If
tape number is found, it will be shown on the
TV screen if “SUPERIMPOSE” is set to “ON”
(੬ pg. 57).
● The counter is reset automatically, however, it
is not completely reset to “0:00:00”.
● If the cassette’s record safety tab has been
removed, playback begins automatically.
2
Access Video Navigation screen
Press NAVI.
● After pressing
NAVI, it may take a
few seconds to
access the Title
screen while the
VCR searches for
the Video
Navigation information.
3
Select program
Press %fi to select the program you want to
watch, then press OK.
4
Start playback
Press
@
#
to move the arrow to “PLAY”, then
press OK.
Playback starts automatically after the selected
program is located.
VIDEO NAVIGATION
VCR
TV
CABLE
/DBS
A
-2,3
A
-1,4
3 - 4
2
BLANK NAVI. SET UP
SEARCH LIBRARY
1. SYDNEY OLYMPIC
PLAY STOP DELETE EDIT
0107 ALL SPORTS TAPE
BLANK 2:00 (LS3) 1 / 3
SELECT
OK
2. FOOTBALL
3. EURO 96 ENGLAND
4. PROJECT XYZ
SYDNEY OLYMPIC [
SHOW]
12/21/02 SAT 6:30 AM – 5:53 PM DBS 256CH LS3
SELECT WITH ARROW KEYS
THEN PRESS [OK]
EXIT
NAVI
Navigation
● Turn on the VCR and the TV, and select the AV
mode on the TV.
● Set the VCR/TV/CABLE/DBS selector on the
Remote to “VCR”.
NOTES:
●
If you press NAVI while Video Navigation is deactivated, the Navigation Set Up screen appears. Set "NAVIGATION" to "ON"
(
੬
pg. 43).
●
Video Navigation playback is possible only with the tape recorded on this VCR.
●
To record the date and time as the program title in this VCR's memory, make sure the VCR’s clock is set correctly before recording.
●
To record the program information in this VCR’s memory, you must record each program for over the minimum recording time; 5
min for the D-VHS (HS) mode, 10 min for the D-VHS (STD) mode, 30 min for the D-VHS (LS3) mode, 50 min for the D-VHS (LS5)
mode, 5 min for the S-VHS/VHS (SP) mode and 15 min for S-VHS/VHS (EP) mode.
●
Video Navigation may not work properly for some tapes.
●
During playback or when searching for the beginning of a program, a VCR might find two different tape numbers recorded on a
tape. After you remove this tape, the tape will be assigned just one tape number (the smaller one). After this, the higher tape
number will be missing from the memory’s tape number list.
●
Tape program information is stored in this VCR’s memory. If this VCR’s memory is damaged and the program information is lost, it
is impossible to restore that information.
●
After recording a tape on this VCR, write the tape number on a label and affix the label to the tape in order to allow you to find the
tape by its number.
●
The on-screen display is output to the TV with S-VIDEO, VIDEO, COMPONENT VIDEO signal in 480i image format.
MV8300_U1B-EN42-47 4/1/3, 2:34 PM42