Mitsubishi Electronics WD-62627 Projection Television User Manual


  Open as PDF
of 118
 
24 Chapter 2. Connecting
Additional connection cables are
not provided with the TV. They are
available at most electronics stores.
IMPORTANT
Connecting a Wall Outlet Cable or Cable Box
Wall Outlet Cable
(can be used with a CableCARD™)
Figure 1
It is very important to connect the incoming cable
for your primary viewing source to ANT-1, especially
for CableCARD™ use and to download TV Guide On
Screen® listings.
1. Connect the primary incoming coaxial lead cable to
ANT 1/MAIN on the TV back panel.
2. For an optional secondary antenna source, connect
an antenna (or cable) to ANT 2/AUX.
3. If you have subscribed to a CableCARD™ service,
the CableCARD can now be inserted into the
CableCARD SLOT. Using a Phillips screwdriver,
remove the CableCARD cover screws. Insert the
CableCARD, then replace the cover and screws. The
top of the card should face in the direction the CARD
TOP arrow indicates.
Additional CableCARD information is on page 20.
Detailed TV Guide On Screen information is in the
separate User’s Manual.
 0QUJPOBM4FDPOEBSZ
"OUFOOBPS$BCMF
 1SJNBSZ8BMM
0VUMFU$BCMF
 $BCMF$"3%
5.
4-05
DPWFSSFNPWFE
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN
ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT
CableCARD™
USE WITH ANT 1 CARD TOP
5P"/5."*/
5P"/5"69
57CBDLQBOFM
TFDUJPO
Figure 1. Wall Outlet Cable
Standard Cable Box
(analog cable box, other than an HDTV cable box,
compatible with PIP)
Figure 2
3 coaxial cables and one two-way RF splitter are required.
These are not included with the TV.
Note: See page 29 to connect an HDTV cable box.
1. Connect the incoming cable to IN on an RF splitter.
2. Connect one coaxial cable from OUT on the RF
splitter to ANT-1 MAIN on the TV back panel.
3. Connect one coaxial cable from OUT on the RF
splitter to IN on the analog cable box.
4. Connect one coaxial cable from OUT on the cable
box to ANT-2 AUX on the TV back panel.
5. After the cable box is connected to ANT-2 AUX
as shown, open NetCommand and go to the RF
Connection for Cable screen and do the following:
a. Check the RF check box.
b. For antenna, select ANT-2.
c. For Channel, select the channel to which the TV
must be tuned for your cable box. The default
channel is 3.
When this setup is complete, you can use the TV remote
control to change channels on the cable box.
DTV/CABLE/
VHF/UHF
ANT 1 / MAIN
ANT 2 / AUX
DIGITAL
AUDIO
OUTPUT
CableCARD™ USE WITH ANT 1 CARD TOP
*/ 065
*/
065
065
5808":41-*55&3
57CBDL
QBOFM
TFDUJPO
*ODPNJOH
$BCMF
$BCMF#PYCBDL
QBOFMTFDUJPO
3'4QMJUUFS
5P"/5."*/
5P"/5"69
Figure 2. Connecting a Cable Box
Note: To use a cable box connected to ANT-2 as
shown above, you must make the noted NetCommand
changes. The changes are required to change
the NetCommand cable-box default connection
(Component-1) to the actual connection (ANT-2).
 previous next