Mitsubishi Electronics WD-Y57aa Projection Television User Manual


  Open as PDF
of 124
 
102 Appendices
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Method 1: Code Entry
1. Movetheslideswitchatthetopoftheremotetothe
positionfortheproductyouwanttocontrol.Referto
thetablebelow.Onlyoneofeachdevicetypecanbe
controlledineachslide-switchposition.
Switch Position Affected Device
CABLE/SAT
CableBox
DTVReceiver
SatelliteReceiver
VCR
VCR
DVR
LaserDiscPlayer
DVDPlayer/Recorder
DVD
DVDPlayer/Recorder
DVR
LaserDiscPlayer
VCR
AUDIO
A/VReceiver
AudioAmplifier
CDPlayer*
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Releasethe
POWER
button.
4. Enterthefirstfive-digitcodelistedforyourequipment.
• The
POWER
buttonblinkstwicewhenyoustartto
enterthecodeandthenonceforeachadditional
keypress.
• The
POWER
buttonblinkstwicewhenyoufinish
enteringavalidcode.
• Movetheslideswitchtoanotherpositionifyou
needtostartoverorwishtoexitprogramming
mode.
5. Pointtheremotecontrolattheequipmentandpress
POWER
. Iftheproducthasnopoweron/offfunction,
pressadifferentkey,suchas (
PLAY
), (
STOP
),
VOL
,or
MUTE.
• Iftheequipmentresponds,theremotecontrolis
properlyprogrammedtooperatetheequipment.
• Iftheequipmentdoesnotrespond,repeatsteps
2–4withthenextfive-digitcodelistedforyour
equipment.
6. Onceyouhavefoundthecorrectcode,writeitinthe
spacebelowforfuturereference.
Switch Position
Device Type Code
CABLE/SAT
VCR
DVD
AUDIO
Method 2: Code Search
Inthismethodofprogramming,youstepthroughthe
remotecontrol’sinternalcodelibrarytofindthecorrect
codeforyourA/Vproduct.
1. Movetheslideswitchatthetopoftheremotecontrol
tothecorrectpositionfortheproduct.Seethetable
under“Method1.”
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 1
4. Pressthenumber
1
,
2
,or
3
dependingontheslide-
switchpositionandthetablebelow.
Switch Position Number
CABLE/SAT
1
DVD, VCR
2
AUDIO
3
5. Press
CH
and
POWER
repeatedlyuntiltheproduct
respondsbypoweringonoroff.Youcanpress
CH
tomovebackwardthroughthecodelibraryifneeded.
NOTE: Iftheproducthasnopoweron/offfunction,check
foraresponseusingadifferentfunction.Press
(
PLAY
), (
STOP
),
VOL
,or
MUTE
andthenre-
peatedlypress
CH
/ tocheckforaresponse.
6. Whentheproductresponds,press
ENTER
tosetthe
code.
Code Verification
Todeterminethecodeprogrammedforanypositionof
theslideswitch:
1. Movetheslideswitchtothepositionyouwishto
verify.
2. Pressandhold
POWER
ontheremotecontrolforseveral
secondsuntilthebuttonblinkstwiceandgoesoff.
3. Presskeys
9 9 0
4. Press
1
andcounttheblinksofthepowerbutton.
Writedownthenumberofblinksasthefirstdigitof
thecode.
5. Repeatstep4forthesecond,third,fourth,andfifth
digitsofthecode.
Appendix D: Programming the Remote Control
 previous next