Panasonic DMR-E80H DVD Recorder User Manual


 
25
RQT6984
Timer recording
You can enter up to 32 programs up to a month in advance.
Each daily or weekly program is counted as one program.
1 Press [PROG/CHECK].
2 Press [ENTER].
3 Press [1] to move through the items
and change the items with [3, 4].
The current settings are shown each time you press [1].
You may use the numbered buttons to enter the CHANNEL,
DATE, ON (start Time), and OFF (Finish Time).
CHANNEL (Channel number and caption)
DATE
[.Current date
l;:
l Next day up to one month later minus one day
l;:
l Weekly timer: SUN-SAT>MON-SAT>MON-FRI
l;:
{.Daily timer: WEEKLY SUN>--->WEEKLY SAT
ON (Start time)/OFF (Finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
MODE (Recording mode page 15)
SP>XP>FR>EP>LP (>Return to SP)
DRIVE
HDD()DVD
RENEW
(Only when you set daily or weekly recording onto HDD
page 26, Auto Renewal Recording)
ON()OFF
Enter Title
Select “Enter Title” using [2, 1] and press [ENTER]
(page 38).
4 Press [ENTER] when you have
finished programming the timer.
Press [3, 4] to select “New Timer Program” and repeat
steps 2- 4 to program other recordings.
5 Press [PROG/CHECK] or [RETURN].
The timer recording list disappears and the unit enters Timer
Recording standby mode (“
F” appears on the unit display).
The unit is not off. To save power, turn the unit off by press-
ing [Í, DVD POWER].
Manually programming timer recordings
CANCEL
TIMER
RECORDING
RETURN
SELECT
MODE DRIVE
CHECK
OFFONNo
CHANNEL
DATE
3/26 TUE 12:55 PM
ENTER
Press ENTER or
VCR Plus+ to
store new program
01 SP Enable2:00 PM1:00 PM64 ABC 3/ 26 TUE
1:42 SP
Remain HDD DVD
17:36 SP
New Timer Program
A line that is
ready for
programming
is highlighted.
TIMER
RECORDING
RETURN
No.
SELECT
3/26 TUE 12:55 PM
ENTER
--
0 9
--:-- --
----------
--:-- --
--
Enter Title
Please set Channel.
1:42 SP
Remain HDD DVD
17:36 SP
MODE
DRIVE
OFFON
CHANNEL
DATE
----
3
4
---
TIMER
RECORDING
3/26 TUE 12:55 PM
3:00 PM
3/ 26 TUE
64 ABC
2:30 PM
SP HDD
Enter Title
1:42 SP
Remain HDD DVD
17:36 SP
MODE
DRIVE
OFFON
CHANNEL
DATE
To release the unit from recording standby
Cancel all the timer recording programs using [CANCEL]
(page 27).
To stop recording when recording has already
begun
Press [], then [ENTER] within 5 seconds on the remote.
Recording stops.
[Note]
When the program timer reaches the set time when in record-
ing standby mode, timer recording will start even if the unit is
playing or recording another program.
The actual time recorded may be longer than the program itself
when television programs are recorded using VCR Plus
i
.
If you don’t select a recording mode when using VCR Plus+
codes to make a timer recording, the unit sets the mode
selected on the unit at that time (unless the mode is “XP”, in
which case the unit sets “FR” as the mode).
“All timer programs are occupied.” appears if there are
already 32 programs.
The remaining time displayed is based on the current record-
ing mode.
When you program successive timer recordings to start
immediately one after the other, the unit cannot record the
part at the beginning of the later programs (a few seconds
when recording with HDD or DVD-RAM, and approximately
30 seconds when recording with DVD-R).
If you set DST (Daylight Saving Time) to ON when manually
setting the clock (page 47), timer recording may not work
when summer switches to winter and vice versa.
F” flashes when the unit couldn’t go to timer recording
standby.
When timer recording starts, the record lamp (page 13,
Main unit) lights, even if the unit is off.
Relief Recording
When the recording drive is set to “DVD” for timer recording, the
unit will automatically evaluate if the program will fit onto the disc
before beginning recording. If the program will not fit then the
recording drive will be altered to “HDD” automatically.
If the time remaining on the HDD is insufficient, as much of the
program as possible will be recorded onto the HDD.
If there is no disc in the tray or the disc cannot be recorded on,
the recording drive will be altered to HDD.
The recording mode will not be altered.
The Direct Navigator shows which programs were relief-
recorded (page 19).
TIMER
RECORDING
MODE DRIVE
CHECK
OFFONNo
CHANNEL
DATE
3/26 TUE 12:55 PM
01 SP Enable2:00 PM1:00 PM64 ABC 3/ 26 TUE
1:42 SP
Remain HDD DVD
17:36 SP
New Timer Program
SP Enable3:00 PM2:30 PM64 ABC 3/ 26 TUE02
Displayed if the
recording can fit
in the remaining
space on the
disc.