Filter
Top Products
57
RQT8023
Convenient
functions
Channel/Clock settings when TV Guide On Screen
TM
system is not used
Refer to the control reference on page 54.
Preparation:
If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1 Press and hold [X CH] and [W CH] on the main unit for about five
seconds.
The unit turns off.
2 Press [Í DVD POWER] to turn the unit on.
3 Complete the TV Guide On Screen
TM
system setup (until [ENTER]
is pressed after the “Watch TV” message screen is displayed).
[Note]
You can set scheduled recording only manually after you set the unit with “Set Channels Automatically”.
1 Press [SETUP].
2 Press [3, 4] to select “Channel” and
press [1].
3 Press [3, 4] to select “Set Channels
Automatically” and press [ENTER].
4 Press [2, 1] to select “Yes” and
press [ENTER].
5 Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥DST, Daylight Saving Time, shows the summertime setting.
≥TIME ZONE shows the time difference from Greenwich
Mean Time (GMT).
EST (Eastern Standard Time) l GMT j5
CST (Central Standard Time) l GMT j6
MST (Mountain Standard Time) l GMT j7
PST (Pacific Standard Time) l GMT j8
AST (Alaska Standard Time) l GMT j9
HST (Hawaii Standard Time) l GMT j10
For other areas: xx hr
≥If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥If the time was not set correctly, use manual clock setting
(➡ 17) or adjust time zone.
6 Press [ENTER].
≥The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone (j1 or i1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
1 Press [SETUP].
2 Press [3, 4] to select “Setup” and
press [1].
3 Press [3, 4] to select “Clock
Settings” and press [ENTER].
4 Press [3, 4] to select “Adjust Time
Zone” and press [ENTER].
5 Press [3, 4] to select “s1” or “r1”
and press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [SETUP].
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
IN2
IN 2
CH
C H
HDD
DVD SD
S VIDEO
S VIDEO
VIDEO
VIDEO
L/MONO
L/MONO
-
AUDIO
AUDIO
-
R
OPEN/CLOSE
OPEN/CLOSE
DRI
DRI
VE
VE
SELECT
SELECT
REC
REC
/x
1.3
X CH W
Auto channel/clock settings
Channel
SETUP
Setup
Disc
Video
Audio
Set Clock Automatically
Auto Clock Setting is complete.
4/4/2005 12:15 AM
DST.............. On
Time Zone..... CST
Signal Source
(RF IN)
Band Channel
Antenna
VHF 2–13
UHF 14–69
CableTV
VHF 2–13
CATV LOW BAND 95–99
CATV MID/SUPER BAND 14–36
CATV HYPER BAND 37–65
ULTRA BAND
66–94
100–125
SPECIAL CATV CHANNEL 1
Adjust Time Zone
SETUP
Setup
Disc
Video
Adjust Time Zone
j1
0
i1
Channel
EH50English.book Page 57 Tuesday, February 1, 2005 6:36 PM