Filter
Top Products
Channel tuning
ç After the installation of the TV channels has been done, always make
a selection in the Installation menu, Installation mode between Antenna
or Cable whether you want to watch Antenna TV channels or Cable TV
channels.
) If you make use of a signal splitter do not forget to put the switch in
the corresponding position.
Available channels:
- Cable (analog NTSC or digital QAM): max. from 1 to 135
-Terrestrial (analog NTSC or digital ATSC): max. from 2 to 69
If a tuned channel is not yet in the master channel map, the TV will
attempt to tune the channel and it will be added to the map.
If the channel is not acquired, a message will appear that the channel is
not available.
When you tune an audio-only digital subchannel, a display appears with
the message Audio only.
ç Subchannel selections
The new standards employed with digital broadcasting make it possible
to receive multiple program channels under a single major channel
number which can be selected by pressing the digit channel number
entry.
ç Digital Channel selection delay
Due to the tuning complexity of subchannel digital programming,the
time to select and view a digital channel may take slightly longer than
what the viewer is normally accustomed to (as compared to analog
channel programs).
Digital channel broadcasts contain program and system data information
that must be processed before the channel selection can be displayed.
_________________________
7.3.1 Installation update
This allows you to automatically tune to and update all available
channels, without altering the sorting of existing channels.
ç - New channels found will not be added to any favorite list.
- Already installed channels will not be renumbered.
_________________________
7.3.2 Weak channel installation
This allows you to manually tune weak ATSC channels in order to adjust
the antenna and thus optimize signal quality for that channel.This only
available for TV channels installed via an antenna connection.
‡ Select a channel in the displayed list of TV channels (in the antenna
mode).
® The signal strength is displayed and updated continuously as you
rotate the antenna.
_________________________
7.3.3 Installation mode
This allows you to select the already stored terrestrial or cable TV
channels. Choose for Antenna or Cable whether these signals are
present.
_________________________
7.3.4 Channel edit
This allows you to rename, to reshuffle and to uninstall or reinstall the
stored channels.
< Press the corresponding color button and follow the on screen
instructions.
_________________________
7.3.4.1 Rename
This allows you to change the name stored in the memory or to assign a
name to a channel for which a name has not yet been entered.
‡ Select the channel you want to rename.
® Press the red color button on your remote control.
ÒSelect the characters with the cursor up/down. Select the following
position with the cursor right.
† Press the green color button or the
OK button when finished.
à - Press the yellow color button to delete all characters.The cursor
is positioned at the beginning again;
- Press the blue color button to delete the character the cursor is
positioned. Enter a new character with the cursor up/down;
- A name can be given to the channel numbers 0 to 999;
- Space, numbers and other special characters are located between Z
and A.
º Select another channel number and repeat steps 2 to 5.
_________________________
7.3.4.2 Uninstall - reinstall
This allows you to uninstall a stored channel so that it is no longer
possible to tune to.This also allows you to reinstall an earlier uninstalled
channel.
‡ Select the channel you want to uninstall.
® Press the green color button to uninstall the selected channel.
> The uninstalled channel is indicated in the list by an icon in front
of the uninstalled channel.
ÒPress the green color button again to reinstall the uninstalled
channel.
ç Uninstalled channels are not reinstalled during an installation update.
18
Info
TV menu / Installation
Channel installation
Autoprogram
Installation update
Weak channel installat..
Installation mode
Channel edit
Channel edit
0
1
2
3
4
......
Info
TV menu / Installation
Channel installation
Installation update
Start now
Autoprogram
Installation update
Weak channel installat..
Installation mode
Channel edit