Filter
Top Products
47EN
Recording
Playback EditingIntroduction Connections Basic Setup Function Setup Others
47EN
DV DUBBING
Guide to DV and On-Screen Display
This function helps you to easily dub the contents of the DVC (digital video camcorder) to DVD.
You can control basic operations of the DV from the remote control of this unit such as playback, fast forward or
reverse and stop all operations if the DV camcorder is in playback mode. Use the DV cable that has 4-pin input jack and
is compliance with the IEEE1394 standards. When you connect to DV-IN jack on the front of this unit, select “E3”
position by using [SOURCE] or [CH / ] on the remote control and press [INFO] to show the DV dubbing
information for the operating your DV camcorder.
1. DV icon
2. Indicator of active device
• When the “Control” is
highlighted, press [OK] to display
the item selection. Use [K / L] to
select the device you wish to
operate, then press [OK] to
activate.
• Select “DVD” to control this unit.
• Select “DV Input” to control your
DV camcorder.
3. Recording audio mode
• Other than the DV camcorder is in
stop mode, the “DV Audio” can be
selected. Press [OK] to display the
item selection and then use
[K / L] to select the audio you
wish to output. Press [OK] again
to activate.
• Select “Stereo1” to dub the stereo
sound.
• Select “Stereo2” to dub the sound
with after recording sound.
• Select “Mix” to dub the stereo1
and stereo2.
4. Indicator of dubbing function
• When the unit is ready for
dubbing, “Start Rec” will appear.
• When the unit is in dubbing,
“Pause Rec” will appear.
5. Channel position
• When you select “E3” by using
[SOURCE] or [CH
/ ], “E3 (DV-
IN)” will appear.
DVD+RW1 1 0:00:00
SP (2Hr) 1:35
AB-1234
0:00:00
E3 (DV-IN)
DV Audio Stereo1
Start Rec
Control DVD
DVD+RW1 1 0:00:00
SP (2Hr) 1:35
AB-1234
0:22:54
E3 (DV-IN)
2
3
1
4
5
7 6
The menu changes according to
what mode of DV camcorder.
Switch the mode on the DV cam-
corder to playback mode for the
dubbing information.
When the DV camcorder is in
playback mode...
When the DV camcorder is
not in playback mode...
6. Product name of your DV
camcorder
• If the unit cannot recognize the
input signal from the DV
camcorder or the unknown
product, “No Device” or “****” will
appear instead.
7. Status of the current operation
and the time counter
Each icon means:
DVC is in stop mode.
DVC is in playback mode.
DVC is in pause mode.
DVC is fast forwarding.
(standard speed)
DVC is fast forwarding.
(faster than above)
DVC is fast forwarding.
(faster than above)
DVC is slow forwarding.
(standard speed)
DVC is slow forwarding.
(faster than above)
DVC is slow forwarding.
(faster than above)
DVC is fast forwarding.
(in stop mode)
DVC is fast reversing.
(in stop mode)
DVC is fast reversing.
(standard speed)
DVC is fast reversing.
(faster than above)
DVC is fast reversing.
(faster than above)
DVC is in slow reverse
playback.
DVC is in recording.
DVC is in recording pause
mode.
The following instructions are described with the operations using the remote control of this unit.
E7C40UD.indd 47E7C40UD.indd 47 2007/01/15 11:19:502007/01/15 11:19:50