Filter
Top Products
8
To Skip a Preset Channel
The channels you can no longer receive or seldom watch can
be set to be skipped when you access channels CH + or CH -.
• Use the remote control for this procedure.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select “INITIAL”, then press B.
3 Press K/L to select “CH TUNING”,then press B.
4 Press K/L to select “MANUAL”,then press B.
5 Press K/L to select “SKIP”,then press B.
6 Use numerical key pads or K/L to
select relevant position number,
then press B.
7 Press K/L to select “SKIP”,then
press B to select “ON”.
• To memorise the channel again,
press B. “ON” will change to
“OFF”.
8 Press DISC/VCR MENU to exit.
Note:
– To confirm that a channel has been deleted,press CH +
or CH -.
Setting the clock
If the display shows an incorrect time or “ --:-- ”, the time and
date must be reset manually.
• This unit incorporates a 24-hour clock.The clock must be set
for the Automatic Timer Recording function to operate
correctly.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select “INITIAL”, then press B.
3 Press K/L to select “CLOCK”,then press B.
4 Press K/L until the relevant year
appears,then press B.
5 Likewise, set the relevant month,
day,hour and minute.
6 Press DISC/VCR MENU to start
the clock.
Notes:
– In the steps 4 and 5,you can
go back to the item you want to correct by pressing s .
– Although seconds are not displayed,they begin counting
from 00 when you exit by pressing DISC/VCR MENU.
Use this feature to synchronise the clock with the
correct time.
– When unplugging the power-cord or if there is a power
failure for more than 1 minute, you may have to reset
the clock.
Setting Up your DVD/ VCR
Automatic Channel Setup
You can programme the tuner to scan only the channels that
you can receive in your area.
• Use the remote control for this procedure.
1 Turn on the TV and select the TV channel to the video channel
on the TV.
2 Press VCR, then DISC/VCR MENU.
3 Press K/L to select “INITIAL”, then press B.
4 Press K/L to select “CH TUNING”,
then press B.
5 Press K/L to select “AUTO”,then
press B.
• The tuner scans and memorises
all the active channels in your
area. After scanning, the tuner
stops on the lowest memorised
channel.
Manual Channel Setup
• Use the remote control for this procedure.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select “INITIAL”, then press B.
3 Press K/L to select “CH TUNING”,then press B.
4 Press K/L to select “MANUAL”,then press B.
5 Press K/L to select “POSITION”,
then press B.
• When a weak signal is received in
Manual Tuning mode,you can
change the background to solid
blue or the static screen by
pressing CLEAR.
6 Use numerical key pads or K/L to
select your desired position number,then press B.
• You can select position number 01-99.
• If “ON” appears on the right side of “SKIP”, press K/L to
point to “SKIP”. Then press B to select “OFF”.
• Press K/L to select “BAND”,then press B repeatedly until
the desired BAND is indicated.
7 Press K/L to select “PPPPPPPPPP”,then press s / B
to start scanning.
• The unit’s tuner will begin to search up or down
automatically.When a channel is found, it will stop searching
and the picture will appear on the TV Screen.
8 Press DISC/VCR MENU to exit.
Note:
– To select any existing channels (including the ones
deleted),use numerical key pads.To flip through only the
memorized channels,use
CH + or CH -
.
MANUAL
BPOSITION P08
PPPPPPPPPPPPPPPP
BAND [UHF]
SKIP [OFF]
CLOCK
BYEAR 2 0 0 6
MONTH 0 1
DAY 0 1 SU
HOUR _ _
MINUTE _ _
CH TUNING
BAUTO
MANUAL
To Select a Desired Channel
You can select a desired channel by using the CH + or CH -,or
directly pressing the numerical key pads on the remote control.
• Enter a channel numbers as a two-digit number for the quickest
results.For example,to select channel 6, press 0 and 6.If you
only press 6,channel 6 will be selected after a brief delay.
• You can only select channels 1-99.
MANUAL
POSITION P08
PPPPPPPPPPPPPPPP
BAND [UHF]
BSKIP [OFF]
Tuner channel
VHF L: 45.75~138.25MHz
VHF H: 140.25~423.25MHz
UHF: 427.25~855.25MHz
Picture Select
This function enables you to select the picture quality of a tape.
• Use the remote control for this procedure.
1 Press VCR, then DISC/VCR MENU.
2 Press K/L to select “SET UP”,then
press B.
3 Press K/L to select “PICTURE”,
then press B.
4 Press B repeatedly until the
desired mode (NORMAL,SOFT or
SHARP) is indicated on the TV
screen.
Notes:
– If the On screen menu still
remains, press DISC/VCR
MENU to exit the menu.
– Once you select the Picture
Select mode, it stays in effect
even after you turn off the unit.
– When you use this function
during playback,you can select a mode (NORMAL,
SOFT or SHARP) as you watch video image.
MENU
TIMER
BSET UP
INITIAL
SET UP
AUTO REPEAT
[ON]
B
PICTURE [NORMAL]
E8B23AD_EN 5/16/06 12:03 PM Page 8