Filter
Top Products
3
Table of Contents
CAUTION
• To prevent injury and material damage, thoroughly read
this manual and all labels found on the equipment before
attempting to mount, install, move, or adjust the product.
• Do not install the unit outside or in the open air. Doing
so will lead to water seepage into the system, resulting
in fire or electric shock.
• Be especially careful when working around parts of the
system that have sharp edges.
• When performing installation work from a height, take
suitable precautions to guard against falling. Set up a
barrier around the work site to prevent accidentally
dropped objects that can injure people standing or
walking below. Tampering with the unit may result in
fire or electrical shock.
• Keep all foreign objects out of the unit. Tampering with
the unit may result in fire or electrical shock.
• Observe the following operating environmental
limitations:
Temperature: 0 °C to 40 °C
Humidity: 20 % to 80 %
• Install the unit only in properly ventilated areas.
5.3 Menu Mode............................................................... 173
5.3.1 About menu mode .......................................... 173
5.3.2 Concerning the display of the OSD of
each item ........................................................ 173
5.3.3 Example of a Menu Mode Operation.............. 174
5.3.4 Adjustment and setting in the Menu Mode .... 175
1) Power Management Setting .................... 175
2) Signal Format Setting ............................... 176
3) Menu Language Display Setting............... 177
4) Energy Saving Setting .............................. 178
5) Timer Setting ............................................ 180
6) Program/Repeat Timer Setting ................. 180
7) Orbiter Setting .......................................... 181
8) Soft Focus Setting .................................... 182
9) Auto Set Up Mode Setting ....................... 183
10) Screen Position, Clock Frequency and
Clock Phase Adjustment .......................... 184
11) Auto Function Mode Setting .................... 186
12) PIP DETECT Setting ................................. 187
13) SPLIT FREEZE Setting .............................. 188
5.3.5 Concerning the display of the OSD of each item
(Applicable only when a PDA-5003/PDA-5004
is installed.) ..................................................... 189
5.3.6 Example of a Menu Mode Operation
(Applicable only when a PDA-5003/PDA-5004
is installed.) ..................................................... 189
5.3.7 Adjustment and setting in the Menu Mode
(Applicable only when a PDA-5003/PDA-5004
is installed.) ..................................................... 190
1) Color Temperature Setting ....................... 190
2) Power Management and Auto Power
OFF Setting .............................................. 191
3) DNR (digital noise reduction) Setting........ 192
4) MPEG NR Setting ..................................... 193
5) CTI Setting ................................................ 194
6) PURECINEMA Setting .............................. 195
7) Color Decoding Setting............................. 197
8) Color System Setting................................ 198
9) Signal Format Setting ............................... 199
10) DVI Setting ............................................... 201
11) Menu Language Display Setting............... 202
12) Energy Saving Setting .............................. 203
13) Timer Setting ............................................ 205
14) Program/Repeat Timer Setting ................. 205
15) Orbiter Setting .......................................... 206
16) Soft Focus Setting .................................... 207
17) Auto Set Up Mode Setting ....................... 208
18) Screen Position, Clock Frequency and Clock
Phase Adjustment .................................... 209
19) Auto Function Mode Setting .................... 211
20) PIP DETECT Setting ................................. 212
21) SPLIT FREEZE Setting .............................. 213
5.4 Integrator Mode ....................................................... 214
5.4.1 About the Integrator Mode ............................. 214
5.4.2 Example of Integrator Mode Operation .......... 215
5.4.3 Adjustment and Setting in the Integrator
Mode............................................................... 216
1) PICTURE Adjustment ............................... 216
2) WHITE BALANCE Adjustment ................. 217
3) COLOR DETAIL setting ............................ 218
4) GAMMA Setting ....................................... 219
5) SCREEN (Screen Position) Adjustment .... 220
6) Brightness Enhancement (BRT. ENHANCE)
Setting at the Center of the Screen.......... 221
7) SUB VOLUME Setting .............................. 222
8) Program Timer Setting ............................. 223
9) SCREEN MASK Setting ............................ 225
10) SIDE MASK Setting .................................. 226
11) VIDEO WALL Setting ............................... 228
12) BAUD RATE Setting ................................. 232
13) Assigning an ID......................................... 233
14) Cooling Fan Control Setting ...................... 235
15) OSD Display Setting ................................. 236
16) FRONT INDICATOR Setting ..................... 238
17) COLOR MODE Setting ............................. 239
18) PRO USE Setting ...................................... 240
19) FRC Setting .............................................. 242
20) POWER ON MODE Setting...................... 244
21) SEAMLESS SW Setting............................ 246
22) MIRROR MODE Setting ........................... 247
23) MULTISCREEN Setting ............................ 249
24) REPEAT TIMER Setting ............................ 253
25) FUNCTIONAL LOCK ................................. 255
26) Center Position Display ............................ 256
5.4.4 PICTURE, White Balance and SCREEN Position
Adjustment Values Memory Area Tables ....... 257
5.5 RS-232C Adjustment ................................................ 262
5.5.1 About the RS-232C Adjustment...................... 262
5.5.2 Interface .......................................................... 263
5.5.3 Combination Connection................................. 264
5.5.4 ID Assignment ................................................ 265
5.5.5 List of RS-232C Commands............................ 267
5.5.6 QUEST Commands ......................................... 275
5.6 Screen Burning ........................................................ 283
5.7 Precautions on Connecting Camera Images ......... 285
5.8 Concerning frame delay (lip sync).......................... 285
PRECAUTION
6.1 Precautions ............................................................... 286
MAINTENANCE .................................................................. 287