Filter
Top Products
65
Troubleshooting
Incorrect operations are often mistaken for trouble and
malfunctions. If you think that there is something wrong
with this component, check the points below.
Sometimes the trouble may lie in another component.
Inspect the other components and electrical appliances
being used. If the trouble cannot be rectified even after
exercising the checks listed below, ask your nearest
PIONEER authorized service center or your dealer to
carry out repair work.
The disc table comes back out automatically, shortly
after the disc table is closed.
The disc is dirty or warped.
\ Refer to “Disc Care” (page 62).
The disc is not placed properly on the disc table.
\ Use the disc table guide to align the disc (page 25).
Region number does not conform with this unit.
\ If the region number on the disc does not match
the number on the player, the disc cannot be used
(page 68).
There is condensation on the operating section of the
player.
\ Allow time for condensation to evaporate. If player
is near an air conditioning unit, you should move
the player (page 63).
Playback is not possible.
The disc has been loaded upside down.
\ Check that the disc has been loaded with the label
side facing up.
mark appears on screen.
The selected function does not operate for that disc.
mark appears on screen.
The operation is prohibited by the player.
Picture playback stops and the operation buttons
cannot be used.
\ Stop disc playback (press STOP 7), then start
playback again.
\ Press STANDBY/ON or POWER on the front
panel to turn the player off, and then turn the
power back on again.
New settings made in the Setup screen menus while
a disc is playing are ineffective.
Some settings can be changed while a disc is playing,
but are not effective. This is not a malfunction.
\ Make the same setting when the player is stopped.
\ Stop disc playback (press STOP 7), then start
playback again. When playback is resumed, the
new settings should be in effect. Please note that
making settings in the Setup screen menus may
cancel the resume function.
When making changes in the Setup screen menus,
is displayed.
There is a Video CD or CD loaded in the player and the
setting that was changed only applies to DVD
performance.
\ The settings will be effective the next time a DVD
is loaded.
Settings are canceled.
When the power is turned off by power failure or by
unplugging the power cord, settings will be canceled.
\ Before unplugging the power cord, press
on the remote control checking that “--OFF--”
disappears in the display (U.S. and Canadian
models). Additionally, press POWER on the front
panel to turn the player off (other models).
No picture.
Connection is incorrect.
\ Check that cord connections are correct and that
plugs are firmly connected.
Player settings are incorrect.
\ Check that the VIDEO OUT SELECT switch is set
firmly in the correct position.
\ Check that the TV SYSTEM switch is set to the
correct setting (except for U.S. and Canadian models).
Operation (settings) of TV or AV amplifier is not
appropriate.
\ Be sure that your TV, receiver, or amplifier is set
up to view DVD playback.
The screen is stretched or aspect does not change.
The multi aspect setting is not appropriate.
\ Change the aspect setting in the [TV Screen]
setting in the Setup screen Video menu to the
screen type most appropriate to the TV or monitor
you are using (page 34).
The screen is suddenly squeezed when the Setup
screen is opened.
If the Setup screen is opened during playback of a
DVD being viewed in the letter box format, the screen
may switch to the wide screen format.
\ This is not a malfunction. The screen will return to
normal when the Setup screen is closed.
Picture disturbance during playback or dark.
This player is compatible with Macro-Vision System
copy guard. Some discs include a copy prevention
signal, and when this type of disc is played back,
stripes etc., may appear on some sections of the
picture depending on the TV.
\ This is not a malfunction.
The position of the TV SYSTEM switch was changed
during player operations (except for U.S. and Canadian
models).
\ Switching the position of the TV SYSTEM switch
is not effective if a disc is playing. Stop playback
before performing this operation.
Discs respond differently to particular player functions
which may result in the screen becoming black for a
brief instant or shaking slightly when the function is
executed.
\ These problems are largely due to differences
between discs and disc content and are not
malfunctions of this player.
When recorded on a VCR or passed through an AV
selector, there is disturbance in the playback picture.
This is not a malfunction.
\ Due to the player’s copy protection circuits,
connection of this device through a VCR or an AV
selector may prevent recording or cause picture
problems.
ADDITIONAL
INFORMATION