Filter
Top Products
20
Using the Remote Control
SEARCH
MUTE
PREV CH
DISPLAY
INPUT
TV•VCR
CLEAR
SPEED
REW
PLAY FF
STOP
PAUSE
REC
MENU
PROG
•
SLOW
TRACKING
V
C
R
S
A
T
•
C
A
B
L
E
VCR•
DV
D
A
U
X
C
H
A
N
C
H
A
N
6
1
4
7
3
9
2
5
8
0
PWR
TV
VOL
VOL
C
M
EDIT
+
_
1
2
F.ADV
e
MOVE
AUX (Auxiliary)
Can be programmed to control a
compatible RCA audio or video
component. See page 25.
SAT•CABLE
Turns on a compatible cable box or
satellite receiver. See page 24.
Used with PWR button to turn on
another brand of cable box or
receiver, other than RCA, when the
remote is programmed to control
that cable box or receiver. See
page 24.
TV
Turns on a compatible RCA,
ProScan, or GE TV and sets the
remote to control the TV.
Used with PWR button to turn on
another brand of TV, other than
RCA, when the remote is
programmed to control that TV.
See page 23.
VCR1
Turns on a compatible RCA,
ProScan, or GE VCR and sets
remote to control the VCR.
VCR2•DVD
Turns on a compatible RCA,
ProScan, or GE VCR and sets
remote to control VCR when it has
been setup. See page 22.
Used with PWR button to turn on a
compatible RCA or ProScan
LaserDisc player. See page 22.
Can also be programmed to control
a compatible RCA DVD component.
CHAN Up or Down
Selects next higher or lower channel
in the VCRÕs channel memory.
CLEAR
Resets time counter to 0:00:00.
Allows you to change entries when
setting the clock or VCR for a VCR
Plus+ or timer recording.
DISPLAY
Shows VCR operating displays on
the TV screen.
Displays program information
when available.
Displays the time counter.
EDIT
Signals two properly connected
compatible VCRs to begin copying
a tape. See page 48.
F.ADV (Frame Advance)
Lets you view one frame with each
press of the button while the tape is
paused.
FF (Fast Forward)
Fast forwards the tape when the
VCR is stopped.
Searches the picture in forward
motion during playback.
INPUT
Turns the line input on or off.
L1 or L2 will appear in the VCRÕs
display panel and VIDEO1 or
VIDEO2 will appear on the TV
screen.
Line input refers to the signal
coming from the component
connected to the audio/video input
jacks on the back (L1) or front (L2)
of the VCR.
MENU•PROG
Displays the VCR MAIN MENU on
the TV screen.
Removes a menu from the screen.
MOVE Arrow Buttons ( )
Allow you to move through the
menus, enter data and change
settings of selected features.
See page 10.
Numbers (0 through 9)
Select a channel up to 99 by
pressing two numbers.
Select a cable channel over 99 by
pressing and holding 1 until 1– –
appears on the screen. Then press
the other two numbers.
Component Buttons
Press one of the buttons to set the remote to operate that component.
Remote Control
Your back-lit remote has a light button ( ) that glows in the dark. Press this button to light the buttons on the remote. The remote
buttons remain lit when they are pressed within a few seconds of each other. If a button is not pressed within approximately eight
seconds, the light turns off to conserve battery power.
VCR Function Buttons
Press VCR1 (VCR2•DVD) to set remote to control the VCR to use the function