Filter
Top Products
ENG-12 ENG-13
Auto Channel Memory
Auto Channel Memory will automatically seek and store
all active channels in your area.
1 Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
2 Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
3 Select “Channel”
Using the UP/DOWN buttons, move the selection
bar to “Channel”, then press ENTER to select.
4 Run “Auto channel memory”
Move the selection arrow to “Auto Channel
Memory,” then press ENTER to select.
• The DVD-VCR will automatically search for all
available channels in the selected Tuner Band.
This procedure may take a few minutes to
complete.
• When finished, the lowest channel found will be
displayed.
Ant./Cable : Cable TV
Auto Channel Memory
Channel Add/Delete
Language : English
Front Display : Auto
Auto Power Off : Off
Tuner Band Setting
This feature allows you to manually set the DVD-VCR’s
tuner band to Antenna or Cable, whichever you
connected to the Antenna In jack during initial setup.
• Use this setting only if Auto Setup detected the
incorrect tuner band, i.e. channels are coming in on
the wrong channel numbers.
1 Open “MENU”
With the DVD in Stop or Play mode, press the
MENU button.
2 Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
3 Select “Channel”
Using the UP/DOWN buttons, move the selection
bar to “Channel”, then press ENTER to select.
4 Select “Ant./Cable”
Move the selection arrow to “Ant./Cable” then press
right to select from the following options:
• Antenna - Indicates that the DVD-VCR is
connected to an indoor or outdoor VHF/UHF
antenna.
• Cable TV - Indicates that the DVD-VCR is
connected to Cable TV.
Language : English
Front Display : Auto
Auto Power Off : Off
Ant./Cable : Cable TV
Auto Channel Memory
Channel Add/Delete
Cable TV
Antenna
Menu Language Manual Clock Set
To change the on-screen MENU language to English,
French or Spanish, follow these steps.
1 Open “MENU”
Press the MENU button while the DVD is in Stop or
Play mode.
2 Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
3 Select “Language”
Use the UP/DOWN buttons to highlight “Language”
then press the ENTER button.
4 Set menu Language
Place the selection bar next to your desired
Language, then press the ENTER button.
If Auto Setup fails to set the DVD-VCR’s internal clock
by locating a local TV station, follow these steps to set
the date and time manually.
NOTE: For accurate Timer Recording, your DVD-VCR's
internal clock must be set correctly.
1 Open “MENU”
Press the MENU button while the DVD is in Stop or
Play mode.
2 Select “SETUP”
Using the UP/DOWN buttons, move the selection
bar to “SETUP” then press ENTER to select.
3 Select “Clock”
Use the UP/DOWN buttons to highlight “Clock ”
then press the ENTER button.
4 Select “Manual Clock”
Move the highlight to “Manual Clock”, then press
the ENTER button.
• The Clock Set/Adjust menu will change as shown.
5 Set the Clock
Use the LEFT/RIGHT buttons to select each of the
following options, then use the UP/DOWN buttons
to set each option:
• Hour – Set the hour • Month – Set the month.
• Minute – Set the minute. • Day – Set the day.
• Year – Set the year
6 Confirm Settings
Press the RETURN button to confirm your clock
settings and to return to the Clock Set/Adjust.
• Press the RETURN button three times to exit the
menu.
Front Display : Auto
Auto Power Off : Off
Language : English
Language : English
Front Display : Auto
Auto Power Off : Off
Language : English
Front Display : Auto
Auto Power Off : Off
Manual Clock
2004 THU
00368A DVD-V4600/XAC-ENG 12/5/03 10:24 AM Page 12