Filter
Top Products
31EN
Recording Disc Playback EditingBefore you start Connections Getting started
Changing the
Setup menu
OthersVCR functions
Recording
8
Press [ENTER] when all informa-
tion required is entered.
Your programme setting is
stored.
• To set another programme,
repeat steps 2 to 8.
• To exit, press [TIMER PROG.].
• If the recording times of two
or more programmes overlap,
“Overlap” and overlapped
programme numbers are
displayed. (See pages 32-33.)
9
Press [T-SET].
The icon will appear on the
front panel display and the unit
enters to the timer-standby
mode.
1 2 3
6
54
7
0
8 9
MENU LISTTOP MENU
STOP
PLAY
FWD
REV
SKIP
PROG.
CLEAR/C-RESET
VCR
REC/OTR
DVD
REC/OTR
PQRS TUV WXYZ
GHI JKL MNO
.@/: ABC DEF
SPACE DISPLAY
ENTER
ZOOM
REC MODE
VCR
RAPID PLAY
DVD
CM SKIP
SETUP
T-SET
OPEN/CLOSE
EJECT
TIMER PROG.
DUBBING
RETURN
OPERATE
Timer Recording
1
2
3
4
5
6
7
8
9
You can set the unit to record up
to 8 programmes, up to a month
in advance. Daily or weekly
programme recordings are also
available.
• Be sure to set the clock before
entering a timer programming.
Insert a recordable disc or a
tape with a record tab.
1
In stop mode, press
[TIMER PROG.].
Timer Programming list will appear.
Timer Programming
2. - - -
1. - - -
Date Start End CH Mode
DVD
VCR
DVDVCR
2
Select a programme that is not
set using [Cursor K / L], then
press [ENTER].
3
Enter the date using [Cursor
K / L], then press [Cursor B].
Timer Programming
2. - - -
1. 01/01 --:-- --:-- P01
Date Start End CH Mode
DVD
VCR
DVDVCR
Each time you press [Cursor L]
at the current date, the timer
recording date will change as
follows.
e.g., 1st January
Daily
M-F
(Mon.-Fri.)
01/01
31/01
W-SAT
W-FRI
W-SUN
4
Enter the time to start and to
end using [Cursor K / L], then
press [Cursor B].
Timer Programming
2. - - -
1. 01/01 12:00 --:-- P01
Date Start End CH Mode
DVD
VCR
DVDVCR
5
Select the channel number to
record using [Cursor K / L],
then press [Cursor B].
Timer Programming
2. - - -
1. 01/01 12:00 13:00 P01
Date Start End CH Mode
DVD
VCR
DVDVCR
To record from the external input,
select “AV1”, “AV2”, or “AV3”.
6
Select the recording media
(“DVD” or “VCR”) using [Cursor
K / L], then press [Cursor B].
Timer Programming
2. - - -
1. 01/01 12:00 13:00 P01 DVD
Date Start End CH Mode
DVD
VCR
DVDVCR
7
Select the recording mode using
[Cursor K / L]. (See page 24.)
Timer Programming
2. - - -
1. 01/01 12:00 13:00 P01 DVD XP
Date Start End CH Mode
DVD
VCR
DVDVCR
Note
• If you have not set the clock, the clock setting window will appear
instead of the Timer Programming list. Continue from step 4 in “Clock
Setting” on page 22 before programming the timer.
• Press [Cursor { / B] to move the cursor in the Timer Programming list.
• If a basic recording or One-touch Timer Recording is in progress on
one component (e.g. VCR) and the timer recording set for the other
component (e.g. DVD) is about to begin, the unit automatically
switches to the programmed channel for timer recording 2 minutes
before the programmed starting time, and the recording in progress
(for VCR) will be cancelled UNLESS their recording channels are the
same. If their recording channels are the same, the timer recording
will start without cancelling the recording currently in progress. In this
case, the recording of the same channel will be made on both DVD
and VCR.
• Cancel the timer-standby mode by pressing [T-SET] before operation
for either DVD or VCR. When finished operating, press [T-SET] to
resume the timer-standby mode.
• In the timer-standby mode, you can turn on the power and use the
component (VCR or DVD) which is not currently timer-programmed.
8