Filter
Top Products
32 EN
Recording
Timer Recording (cont’d)
1 2 3
6
54
7
0
8 9
MENU LISTTOP MENU
STOP
PLAY
FWD
REV
SKIP
PROG.
CLEAR/C-RESET
VCR
REC/OTR
DVD
REC/OTR
PQRS TUV WXYZ
GHI JKL MNO
.@/: ABC DEF
SPACE DISPLAY
ENTER
ZOOM
REC MODE
VCR
RAPID PLAY
DVD
CM SKIP
SETUP
T-SET
OPEN/CLOSE
EJECT
TIMER PROG.
DUBBING
RETURN
OPERATE
In the following example, No.
5 timer programming overlaps
on No. 1 and No. 6 timer
programmes. In such a case, you
should correct the programme
time to clear the overlap.
Timer Programming
2. - - -
3. - - -
4. - - -
7. - - -
8. - - -
Overlap
No.1 6
5. 01/01 12:30 14:00 P02 DVD SP
1. 01/01 12:00 13:00 P01 DVD XP
6. 01/01 13:45 21:00 P12 DVD SEP
Date Start End CH Mode
DVD
VCR
DVDVCR
1
Press [T-SET] so that the
icon disappears from the front
panel display.
2
Press [TIMER PROG.].
Timer Programming list will
appear.
Timer Programming
2. - - -
3. - - -
4. - - -
5. - - -
6. - - -
7. - - -
8. - - -
1. 01/01 12:00 13:00 P01 DVD XP
Date Start End CH Mode
DVD
VCR
DVDVCR
3
Check the information on the
list you will need.
4
To clear the timer program-
ming, select the desired pro-
gramme using [Cursor K / L],
then press [CLEAR/C-RESET].
To correct the timer program-
ming
1) Select the desired programme
using [Cursor K / L], then
press [ENTER].
2) Correct the timer programming
using [Cursor K / L / { / B].
3) Press [ENTER] again.
5
Press [TIMER PROG.] to exit.
6
Press [T-SET] to return to the
timer-standby mode.
To check the timer program-
ming in process
Press [TIMER PROG.].
6
1
Note
• If a timer recording is
proceeding, that programme
is highlighted in red. In such
a case, you cannot select any
other programmes.
• When you check the timer
programming in progress
by pressing [TIMER PROG.]
during operations of the
component (VCR or DVD)
which is not currently used
for the timer recording,
the programme will not be
highlighted. In this case,
you cannot select other
programmings.
Checking, cancelling, or correcting the timer
programming information
To stop the timer recording in progress
Press [STOP C] to stop the disc recording or [STOP C/EJECT A] to
stop the tape recording on the front panel of the unit.
Note
• [STOP C] on the remote
control is not effective.
The error numbers indicate:
If the timer programming did not complete correctly
The error number appears on the
Timer Programming list.
Timer Programming
2. - - -
3. - - -
*
01/01 12:00 13:00 P01 DVD E1
Date Start End CH Mode
DVD
VCR
DVDVCR
The error programme will be
displayed in grey with an asterisk
and have an error number.
The error programme will be
deleted once you check the error
in the programme list, or once
you cancel the timer-standby
mode and re-enter it.
Press [CLEAR/C-RESET] to erase
the selected programme.
E1-22
E37-39
Recording error
E23-24 Unrecordable disc
E25 • Copy prohibited programme
• Cannot record because of the
NTSC / PAL-60 signal is received.
E26-28 Copy prohibited programme
E29 Disc protected
E30 Disc full
E31 Already recorded 99 titles (Video
mode)
E32 Already recorded 99 titles (VR
mode)
E33
Already recorded 999 chapters
E34 No space for Control information
E35 PCA (Power Calibration Area) full
E36
Already finalised Video format disc
E40 • There are some unrecorded
parts due the overlapped timer
programmes.
• Recording did not start at the
start time.
• There is no tape in the cassette
compartment.
• Tape recording reaches to
the tape end during timer
recording.
E41 Power failure
E42 No disc
2
5
6
4