Filter
Top Products
1-9
PFM-42B1, PFM-42B1E
16
(GB)
Using On-screen Menus
qk W-VGA
Select ON to input the W-VGA (852×480) signal.
When you set this item to ON, the VGA input signal
is determined to be 852 × 480. Otherwise, the VGA
input signal is determined to be 640 × 480.
ql CLOSED CAPTION
Displays closed captions.
For details, see “Displaying closed captions
” on page 19
(GB).
w; COLOR SYSTEM
Selects the input signal.
AUTO: to display NTSC, PAL or SECAM signals
443NT: to display NTSC4.43 signals
PAL60: to display PAL60 signals
PAL-M: to display PAL-M signals
wa SCREEN FILL
Selects the point of origin for resizing the picture.
CENTER: Sets the point of origin at the center of
the monitor.
CORNER: Sets the point of origin at the upper-left
corner of the monitor.
ws POWER CONTROL
Sets the length of time until the system goes into the
power saving mode.
For details, see “Controlling Power On/Off Automatically
(Power Control Function)
” on page 33 (GB).
wd SCREEN SAVER
Enables a screen saver to reduce afterimage or
ghosting.
For details, see “Reducing Afterimage/Ghosting (Screen
Saver Function)” on page 31 (GB).
wf TIME SET
Sets the time.
For details, see “Adjusting the time
” on page 19 (GB).
wg LANGUAGE
Selects the on-screen language (English, German,
French, Italian, Spanish or Japanese).
For details, see “Selecting the On-screen Language
” on
page 30 (GB).
MEMORY menu
This menu is used for saving or recalling the settings
in the PIC CONTROL and PIC SIZE menus.
ENTER
MENU
MEMORY
LOAD
SAVE
wj
wh
SELECT SET END
For details, see “Using the Memory Function
” on page 28
(GB).
wh LOAD
Recalls the preset settings.
wj SAVE
Saves the settings.
REMOTE menu
This menu is used for remote control settings.
ENTER
MENU
REMOTE
INDEX No. : 001
REMOTE MODE : TV
REMOTE ONLY : OFF
wl
wk
e;
SELECT SET END
wk INDEX No.
Sets the index number of the monitor.
Note
When you set the number, use the buttons on the
monitor.
For details about the index number, see
“Operating a
Specific Monitor With the Remote Commander
” on page 35
(GB).
wl REMOTE MODE
Selects the Remote Commander mode.
TV: The Sony monitor
’s or the TV’s commander
PJ: The Sony projector
’s commander
OFF: Disables the remote control.
17
(GB)
Using On-screen Menus
Note
When you change the Remote Commander mode, use
the buttons on the monitor. You cannot change the
Remote Commander mode with the Remote
Commander.
For details, see “Using Other Remote Commander
Models” on page 37 (GB).
e; REMOTE ONLY
Select ON to disable the control buttons on the
monitor. The monitor can only be controlled with the
Remote Commander.
To cancel the REMOTE ONLY mode, set REMOTE
ONLY to OFF with the Remote Commander, or press
the MENU button while pressing the 1 (standby)
switch on the monitor. The monitor turns to the
standby mode and the REMOTE ONLY mode is
cancelled.
The setting in this item is still retained when the AC
power cord is disconnected or when you turn on/off
the monitor with the Remote Commander.
STATUS menu
This menu is used for displaying the internal status of
the monitor.
STATUS
MODEL NAME : PFM- 42B1E
SERIAL No. : 2000001
OPERATION : 000001H
SOFTWARE :
Ver
1.00
TEMPERATURE : OK
FAN : OK
ef
ed
es
ea
eg
eh
ea MODEL NAME
Indicates the model name.
es SERIAL No.
Indicates the serial number.
ed OPERATION
Indicates the total number of hours of operation.
Note
The standby mode is not counted as part of the
OPERATION time.
ef SOFTWARE
Indicates the system software version.
eg TEMPERATURE
Indicates whether the internal temperature of the
monitor is normal.
OK: Normal
NG: Unusual
When the internal temperature is unusual, NG is
displayed and the item flashes in red. The STANDBY
indicator on the 1 (standby) switch / indicator section
also flashes.
Note
The “TEMPERATURE NG
” message may appear
when the ventilation holes are blocked or the monitor
is installed in a poorly ventilated location. In this case,
check that the ventilation holes are not blocked and
install the monitor in a well ventilated location. If the
message is still displayed, contact your authorized
Sony dealer.
When the STANDBY indicator flashes or NG is indicated,
see “Self-diagnosis Function
” on page 35 (GB).
eh FAN
Cooling fans are built into this monitor. This item
indicates whether the cooling fans work properly.
OK: Normal
NG: Unusual
When the cooling fans are not working normally, NG
is displayed and the item flashes in red. The
STANDBY indicator on the 1 (standby) switch /
indicator section also flashes.
Notes
•When the “FAN NG” message appears, contact your
authorized Sony dealer.
When the STANDBY indicator flashes or NG is indicated,
see “Self-diagnosis Function
” on page 35 (GB).
•The cooling fans detect the monitor
’s internal
temperature and control the fan rotation. If the
ambient temperature is high, the fan speed increases
and the fan noise will be louder.