Filter
Top Products
7
Connections and Set-up
EN
Programming the remote control
Automatic code search
This method can be used to automatically find the most
appropriate code for your appliance.
1. Switch on the appliance you wish to use the remote control
with.
2. Press the relevant button for this appliance on the remote
control, and while holding this button down, press the
standby button until the light or the appliance buttons of the
remote control come on. Release both buttons.
3. Point the remote control at the appliance and press PLAY.
Wait until the light stops flashing. If the appliance has not gone
into standby mode, press the
PLAY button again to continue
the search for the next set of codes. Repeat this operation
until the appliance goes into standby mode.There are around
20 sets of codes.
4. When the appliance goes into standby mode, switch it on again
without using the remote control. Press the
REV button as
many times as is required to return the appliance to standby
mode.
5. Press the STOP button and hold it down until the light or the
appliance buttons of the remote control go off.
Note:You can cancel the programming operation at any time by
pressing the
EXIT button.
Manual programming
This method involves carrying out a manual search for the codes
to be used for controlling your other appliances.
1. Switch on the appliance you wish to use the remote control
with.
2. Press the relevant button for this appliance on the remote
control, and while holding this button down, enter one of the
codes relevant to your make of appliance (there is a list of
codes at the end of this manual). If the light or the appliance
buttons of the remote control flash you have entered the
wrong code or it is not possible to program the remote
control.
3. Point the remote control at the appliance and press the
relevant button (
VCR, DVD, etc). Press the standby button.
If the appliance does not go into standby mode, try another
code.
Depending on the year of manufacture and the type of appliance,
some functions may not be available. Certain codes may cover
more functions than others.Test the functions you can control and,
if appropriate, try other codes.
Note here the
code(s) which work
best.
When you change the remote control’s batteries, remember to
reprogram it.
Programming the volume control function
If you have programmed the TV remote control to use with other
appliances and these are connected to an amplifier you can also
programme the remote control to adjust the volume when you are
using one of these appliances.The example below describes the
procedure for programming a DVD player.
1. Programme the AMP button on the remote control to use
with the amplifier (refer to page 6).
2. Move the remote control away from the appliances. Press the
-
button and while holding it down, press the relevant
mode button (
DVD, in this example),then the AMP button.
Release the
-
button.
3. Switch on the amplifier, then the DVD player.
4. Set the remote control to DVD, play a disc and adjust the
volume using the
+/-
buttons.
Repeat this operation for the other appliances.
To cancel the programmed function for any of the appliances, press
the
-
button, while holding it down and enter the code 000
using the numeric buttons.
Video recorder DVD player Satellite receiver Hi-fi system
Press the
VCR
button Press the
DVD
button Press the
SAT
button Press the
AMP
button
On/Standby On/Standby On/Standby On/Standby
MENU To display the main menu To display the main menu To display the main menu
Vertical scrolling in menus Vertical scrolling in menus Vertical scrolling in menus
Horizontal scrolling Horizontal scrolling Horizontal scrolling
in menus in menus in menus
OK To confirm an action To confirm an action To confirm an action
EXIT To close a menu To close a menu To close a menu
0-9 To directly access channels To enter numeric values To directly access channels To select a station using
or enter numeric values or select options in menus or enter numeric values its number
PR+/PR- To change channels To change chapters To change channels To change stations
AV To select av input To select av input
REV Rewind Rewind
PLAY Play Play
FWD Fast forward Fast forward
STOP Stop Stop
PAUSE Pause picture Pause picture
REC Record
To switch the sound off and
back on again
+/- To set the volume level
VCR
DVD
SAT
AUX
AMP
42PB120S5-EN2 22/03/05 15:37 Page 7