Toshiba 52X3000A Flat Panel Television User Manual


 
24
Using the TV’s features (General)
The timers
Setting the Time zone - digital only -
This function allows you to manually set the time zone and
override the location that you have chosen during Auto Scan.
This is to be used when you move out of Australia to country
with different time zone. Please note that if you manually
change the time zone setting, all existing entries in the program
timer will become invalid as they are still based on the old time
zone. It is recommended that you delete all the entries in the
program timer before proceeding with steps described below.
1 From the PROFILE menu, press V or U to select Time
zone.
2 Press Y and Z to select the local time zone.
Program Timer - digital only -
This function will set the TV to go to a specific channel at a
certain time. It can be used to view a particular program, or by
setting the mode to daily or weekly, can be used to view a
series of programs.
1 Press M, then Y or Z to select the PROGRAM menu.
2 Press V or U to select Timer, then press Q.
3 Press V or U to select an empty slot to program a timer
or any existing program to be edited, then press Q .
4 Press V and U to select Ch. No. and Y or Z to choose
the channel you want. Press V and U to select Mode and
Y or Z to choose Once, Daily or Weekly. Then use the
Number buttons to set time for Date, Start and End in
24-hour format.
5 Press Q to save. If you have selected a locked channel or
activated Parental Rate, enter password when
prompted.
Note:
If the new entry causes a conflict with the existing entries
(i.e. overlapping recording time), the new entry will not be
saved.
To delete a selected entry:
Press the Red button, then use V or U to select Yes, then
press Q (All fields will be cleared).
Notes:
When a timed program is about to start, an information
screen will appear indicating the change of current channel.
The menus and other channels will not be available during
the timed program unless the program timer is cancelled.
When the program timer expires, the TV switches to the
channel from which it is switched from.
If timer action occurs when the TV is in standby, the TV will
turn on but no picture is seen and no sound is heard.
Selected digital channel will be at the AV OUTPUT terminals
(- page 9). The selected channel can be watched or
recorded via the AV OUTPUT terminals.
When the timer table is empty, the DTV timer LED (
- page
8) will be off. When the timer table contains at least one
entry, the DTV timer LED will be set to red.
If timer action is in progress, the DTV timer LED will be
changed from red to yellow.
If Menu or EPG is still open when timer action is scheduled
to start, the Menu or EPG will be closed automatically and
then the timer will start.
The correct operation of the Timer depends on the
information received from Broadcaster’s stream.
The time, and the deletion of service are examples of such
information. When broadcaster decides to delete any
channel, the respective entries will then be deleted from the
Timer-table.
It is not the malfunction of the TV.
PROFILE
Audio Preference
Time Format
Time zone
DIGITAL SETTINGS
24 hr
Back Watch TV Select Function
Transparency
I-Plate Display Time
GMT +08:30
1 sec
70
PROGRAM
Channel List
Favorite Mode
Parental Rate
EPG
Alarm
Timer
DIGITAL SETTINGS
No Block
Back Watch TV Select Function
On
Tuesday, 11 Nov 2008 06:44
Channel Name
Ch. No.
Channel 5
Channel 8
Channel U
Start End Date
Mode
0006
0008
0009 00:00
00:00
00:00
00:00
Channel News Asia
0007
00:00
00:00
11 Nov 2008
Daily
Daily
Once
20:30 21:00 18 Nov 2008 Weekly-Sat
Timer
Back Watch TV Delete
Edit Timer Select Function
11 Nov 2008
11 Nov 2008
Timer Setting
Start
End
Date
Mode
Name
Channel News Asia
Ch.No.
0007
13:00
14:00
11 Nov 2008
Once
Back
Enter
Select Function