Filter
Top Products
16
Chapter 2: Connecting your TV
62HM15
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
TheaterNet
OUT
IN
AUDIO
AUDIO
IN
S-VIDEO
VIDEO 1 VIDEO 2
OUT 1
IN
DIGITAL
AUDIO OUT
ANT1
CableCARD™
COLOR
STREAM
HD-1
COLOR
STREAM
HD-2
TheaterNet
OUT 2
1
S-VIDEO
IEEE1394
EJECT
L/
MONO
AUDIO
VIDEO
R
L/
MONO
AUDIO
VIDEO
R
PB
PR
Y
L
AUDIO
R
TheaterNet
AUDIO
OUT
VIDEO
OUT
L
R
S-VIDEO
OUT
OUT
IN from ANT
VIDEO AUDIO
OUT to TV
CH 3
LR
LR
CH 4
IN
OUT
OUT
OUT
IN
IN
CH 3
CH 4
Cable box Signal splitter
Connecting a DVD player with S-video, a VCR, and a Cable box
You will need:
one signal splitter
five coaxial cables
two sets of standard A/V cables
Note: If you have a mono VCR, connect L/MONO on the TV
(VIDEO 1) to your VCR’s audio out terminal using the white
audio cable only.
one S-video cable
one pair of standard audio cables
Note:
• If your DVD player does not have S-video, use a standard
video cable instead. Do not connect an S-video cable and a
standard video cable to VIDEO 1 (or VIDEO 2) at the same
time or the picture performance will be unacceptable.
• If your DVD player has component video, see page 17.
• Do not connect the DVD player and VCR to the same set of
A/V inputs on the TV. (See the illustration, which shows the
VCR connected to VIDEO 1 on the TV, and the DVD player
connected to VIDEO 2.)
To view basic channels and access the TV’s features:
Select the ANT 1 video input source.* Use the TV
controls to change channels and access the TV’s features.
To view premium Cable channels:
Turn off the VCR. Select the ANT 2 video input source
on the TV.* Tune the TV to channel 3 or 4 (whichever
channel is vacant in your area). Use the Cable box
controls to change channels.
Note: When you use a Cable box, you may not be able to
use the remote control to program or access certain
features on the TV.
To view the DVD player:
Turn ON the DVD player. Select the VIDEO 2 video
input source on the TV.*
To view VCR:
Turn ON the VCR. Select the VIDEO 1 video input
source on the TV.*
_____________
* To select the video input source, press INPUT on the remote control
(see page 66). To program the TV remote control to operate other
devices, see Chapter 3.
DVD player with S-video
TV
Stereo VCR
From antenna or Cable TV
Note: The VIDEO/AUDIO OUT terminals output signals from the ANT 1,
ANT 2, VIDEO 1, VIDEO 2, and VIDEO 3 terminals when the appropriate input
mode is selected.
To enable the TV Guide On Screen
®
system to work with
your cable box and to use the TV Guide On Screen
®
recording features:
1. Connect the G-LINK
®
cable according to the instructions on
page 25.
2. Make sure the VCR is connected to the A/V OUT terminals
on the TV (see illustration).
3. Set the VCR to the appropriate line input (refer to your VCR
owner’s manual for details), and then turn OFF the VCR.
4. See Chapter 5 for details on setting up the TV Guide
On Screen
®
system.
5. See Chapter 7 for details on using the TV Guide On Screen
®
system.
The unauthorized recording, use, distribution, or revision of television
programs, videotapes, DVDs, and other materials is prohibited under
the Copyright Laws of the United States and other countries, and may
subject you to civil and criminal liability.
#01E012-025_62HM15 5/24/05, 6:16 PM16
Black