Alpine IVA-D105 DVD Player User Manual


 
45-EN
+01GB06IVAD105.fm
ALPINE IVA-D105 68-08564Z59-A (EN)
Set MX Mode of the External Audio
Processor
Before performing the operations below, set MX (Media Xpander)
mode of the PXA-H700 to “AUTO” when the PXA-H700 is connected.
Setting item : MEDIA XPANDER
1
Select ON or OFF of MX by touching [] or [] of
MEDIA XPANDER.
2
Touch [] after setting to ON.
The Media Xpander setup screen appears.
3
Touch [] or [] of the desired MX mode.
Music source (such as radio broadcasts and CDs, excluding AM
radio) level can be set.
MX CD (OFF, CD MX 1 to 3)
CD mode processes a large quantity of data. This data is used
to reproduce the sound cleanly by making use of the data
quantity.
MX CMPM (OFF, CMPM MX 1 to 3) / MX SAT (OFF, SAT MX 1 to 3)
This corrects information that was omitted at the time of
compression. This reproduces a well-balanced sound close to
the original.
MX FM (OFF, FM MX 1 to 3)
The medium to high frequencies become more clear, and
produces well balanced sound in all the bands.
MX DVD (OFF, MOVIE MX 1 to 2)
The dialog portion of the video is reproduced more clearly.
MX AUX (OFF, CMPM MX, MOVIE MX, MUSIC MX)
Choose the MX mode (CMPM, MUSIC, or MOVIE) that
corresponds to the media connected.
The contents of MX set here is reflected to PXA-H700 or PXA-H701.
When OFF is selected, MX effect of each MX mode will be OFF.
Each music source, such as radio, CD, and MP3 can have its own
MX setting.
MX mode does not function when MX is ON for AM radio.
MX CMPM is applied for MP3/WMA/AAC and iPod.
MX SAT is applied for XM, SIRIUS, HD Radio.
The MX setting can be performed only when a source is currently
selected.
X-OVER Adjustment
Setting item : X-OVER
High pass filter can be applied to front/rear speakers, and low pass filter
can be applied to the subwoofer.
1
Touch [] or [] of the speaker to make the desired
adjustment.
If you set the subwoofer LPF, set the front/rear HPF to OFF, or set
the rear/front speaker to “LARGE” in “Speaker Setup” (page 48).
The frequency you set for the subwoofer LPF will automatically be
applied for the speaker that is set to “SMALL” for the HPF.
Therefore, certain frequencies may not be reproduced.
1
Touch [] or [] of X-OVER to select L/R or L+R.
2
Touch [] of X-OVER.
3
Touch [] of the speaker to be adjusted.
The screen changes to the X-OVER screen to be adjusted.
4
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [] or [] of FREQ., then select the cut-off
frequency (crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
Adjusting the Level
Touch [] or [] of LEVEL, then adjust the HPF or LPF
level.
Adjusting the Slope
Touch [] or [] of SLOPE, then adjust the HPF or LPF
slope.
When the speaker is set to the “OFF” mode, the X-OVER for that
speaker cannot be set. Refer to “Setting the Speakers” (page 44).
Check the playback frequencies of the connected speakers before
adjusting.
In order to protect the speakers, there is no OFF setting for the
subwoofer low pass filter (the slope remains the same).
The H.P.F. filter cannot be set to OFF (slope OFF) if Tweeter is
selected for FRONT1 . Or, only the subwoofer is adjustable if
STEREO is selected for the subwoofer.
OFF: Turns off the MX effect of every music source.
ON: Turns on the specified MX mode.
(DVD MUSIC)
This disk contains a large quantity of data such as music clip.
MX uses this data to reproduce the sound accurately.
BassEngine
A.PROCESSOR
L/R: Different adjustment values can be set for the left and
right channels.
L+R: Sets the same adjustment values for the left and right
channels.
+01GB00IVAD105.book Page 45 Monday, January 15, 2007 4:02 AM