Filter
Top Products
RCP 2000 with ISS 506 Support • Operation
Operation, cont’d
3-12
RCP 2000 with ISS 506 Support • Operation
3-13
3. If necessary, select a preview input.
4. To execute a switch with the dissolve effect, press the Take
button, which blinks while the transition is in progress.
-or-
Slide the T-bar up or down to control the dissolve duration
manually.
Using a Cut
A cut transition immediately and seamlessly replaces the
program image with the preview image, in wipe or dissolve
mode. In PIP mode, it closes or opens the PIP window. No
transition effect is applied to the switch.
N
If you want to switch using your current transition
effect, press the Take button instead of the Cut button.
To execute a cut when the RCP is in wipe, dissolve, or PIP mode,
1. If necessary, select the preview input.
2. Press the Cut button. The seamless switch takes effect
immediately. The preview image becomes the new
program image (wipe or dissolve mode) or the PIP
window closes or opens (PIP mode).
N
In PIP mode, you cannot select a cut from the PIP sub-
effects menu; you must press the Cut button to instantly
open or close the PIP window.
Transition Sub-effects
A variety of visual effects are available for transitioning between
the preview and the program displays in wipe and PIP modes.
The sub-effects that are available depend on the display mode in
which the RCP is operating. (See “Setting the Display Mode,”
earlier in this chapter.) You can also set the duration of the
sub-effect.
Sub-effects available in wipe and PIP modes
The sub-effects described in the following sections can be
selected for the transition between the displayed preview and
program inputs in wipe and PIP modes. These sub-effects are
listed on the label shown on the next page, which is located to
the right of the H and V Adjust knobs on the RCP top panel.
01 = Dissolve (PIP only) 10 = Soft Square In 18 = Hard Center In
02 = Soft Right 11 = Soft Square Out 19 = Hard Center Out
03 = Soft Left 12 = Soft Plus In 20 = Hard Curtain In
04 = Soft Up 13 = Soft Plus Out 21 = Hard Curtain Out
05 = Soft Down 14 = Hard Right 22 = Hard Square In
06 = Soft Center In 15 = Hard Left 23 = Hard Square Out
07 = Soft Center Out 16 = Hard Up 24 = Hard Plus In
08 = Soft Curtain In 17 = Hard Down 25 = Hard Plus Out
09 = Soft Curtain Out
Wipe and PIP Sub-effects
33-1635-01 Rev A
03 08
Standard wipes
A standard wipe sub-effect causes the preview image to appear
to unroll over the program image horizontally or vertically. A
standard wipe can have either hard (sharp) or soft (blurred)
edges.
The following standard wipes are available:
• From left to right — Soft Right (#02) or Hard Right (#14)
• From right to left — Soft Left (#03) or Hard Left (#15)
• From top to bottom — Soft Up (#04) or Hard Up (#16)
• From bottom to top — Soft Down (#05) or Hard Down
(#17)
Left to right Right to left Bottom to top Top to bottom
(#02 or #14) (#03 or #15) (#04 or #16) (#05 or #17)
Curtain wipes
A curtain wipe causes the preview image to appear to unroll
over the program image in two directions simultaneously. A
curtain wipe can have either hard (sharp) or soft (blurred) edges.
The following curtain wipes are available:
• In from the left and right edges to the center of the
screen — Soft Curtain In (#08) or Hard Curtain In (#20)
• Out from the center to the left and right edges of the
screen — Soft Curtain Out (#09) or Hard Curtain Out (#21)