Filter
Top Products
Masterpage:Right+
EN 53
Filename [MX1SEU_10Timer Recording.fm]
TIMER RECORDING ON HDD/DVD DECK
Page 53Monday, 6 December 2004 14:01
This function allows you to automatically record a satellite
programme which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the unit’s [L-2 IN/
DECODER] connector and programme the timer on the satellite
receiver. The unit starts or stops recording by the signals input
from the satellite receiver. After recording, the unit’s power shuts
off automatically.
1 Press HDD on the remote to choose the recording deck. You
can also press VHS/HDD/DVD SELECT on the unit repeatedly
to select the recording deck.
2 Set AL-2 SELECTB to ASAT VIDEOB or ASAT S-VIDEOB.
(A pg. 72)
● Also refer to AIMPORTANTB on page 76.
3 Press REC MODE repeatedly to set the recording mode.
4 Press and hold SATj for about 2 seconds to engage the
Automatic Satellite Programme Recording mode. AVB and
ASATjB appear on the front display panel.
NOTES:
● To disengage the Automatic Satellite Programme Recording
mode, press SATj.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
● In step 4, if AVB blinks quickly on the front display panel even
though your satellite receiver’s power is off, Automatic Satellite
Programme Recording will not work properly with that satellite
receiver*. If this is the case, perform AManual Timer
ProgrammingB (A pg. 51) to timer-record a satellite programme.
* Some satellite receivers output signals even if the power is off. Automatic
Satellite Programme Recording is not possible with those satellite
receivers.
●
AVB blinks on the front display panel while Automatic Satellite
Programme Recording is in progress.
● For timer programming of the satellite receiver, refer to the
instruction manual of the satellite receiver.
● Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
● Pressing the unit’s A button while Automatic Satellite
Programme Recording is in progress turns off the unit’s power
and disengages the Automatic Satellite Programme Recording
mode.
● If there are more than one satellite programmes you wish to
record with Automatic Satellite Programme Recording, it is not
possible to set different recording modes for each programme.
● Depending on the type of satellite receiver, the unit may not
record a slight portion of the beginning of the programme or may
record slightly longer than the actual length of the programme.
● If you engage the Automatic Satellite Programme Recording
mode when the satellite receiver’s power is on, the unit will not
start Automatic Satellite Programme Recording even though AVB
blinks on the front display panel. When the satellite receiver
shuts off once and is turned back on again, the unit starts
recording.
● You can also record a programme from your cable system in the
same way if the system has a timer.
● Just Clock (A pg. 86) does not work when the Automatic
Satellite Programme Recording mode is engaged.
Automatic Satellite Programme
Recording
(HDD Deck Only)
ATTENTION:
● Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the unit will start recording
when the satellite receiver’s power is turned on.
● If you have connected another appliance other than a satellite
receiver to the [L-2 IN/DECODER] connector, be sure not to
engage the Automatic Satellite Programme Recording mode;
otherwise, the unit will start recording when the connected
appliance’s power is turned on.
● Automatic Satellite Programme Recording and timer-recording
cannot be done at the same time.
REC MODE
VHS/HDD/DVD
SELECT
SAT#
REC MODE
HDD
CABLE/SAT
DVDTV
● Make sure the satellite receiver is connected to the unit’s [L-2
IN/DECODER] connector.
● Programme the timer on the satellite receiver.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
MX1SEU_00.book Page 53 Monday, December 6, 2004 2:01 PM