Filter
Top Products
Masterpage:Right+
EN 55
Filename [MX1SEU_10Timer Recording.fm]
TIMER RECORDING ON VHS DECK
Page 55Monday, 6 December 2004 14:01
You can programme this unit to timer-record as many as 8
programmes. If you do not know the
a number for the
programme you wish to record, use the following procedure to set
your unit to timer-record the programme.
1 Load a cassette with the record safety tab intact.
2 Press VHS so that the VHS lamp lights up on the unit.
3 Press PROGRAMME to access the Programme screen.
4 Press FG to select
APROGRAMME/CONFIRMB, then
press ENTER access the
Programme Check screen.
5 Press FG to select the blank
number, then press ENTER. The
programme screen appears.
6 Press DE to select ASTARTB,
then press FG to set the desired
start time.
● Each press of FG increases/
decreases the start time in 1-
minute interval.
● To increase/decrease the start
time in 30-minutes interval, press
and hold FG.
7 Press DE to select ASTOPB, then press FG to set the desired
stop time.
● Each press of FG increases/decreases the stop time in 1-
minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold FG.
8 Press DE to select ADATEB, then press FG to set the desired
date.
● The current date appears on the TV screen. The date you enter
appears in its place.
9 Press DE to select ATV PROGB, then press FG to select the
desired channel.
10 Press REC MODE to select the desired recording mode. Or
press DE to select ASP/LPB, then press FG to select the
desired recording mode.
11 Press DE to select AVPS/PDCB, then press FG to select the
desired channel.
12 Press ENTER to access the Programme Check screen.
13 Press PROGRAMME to complete timer programming.
APROGRAM COMPLETEDB appears on the TV screen for
about 5 seconds, then the normal screen appears. If
APROGRAM OVERLAPPEDB appears on the TV screen, see
page 56.
● To programme another timer, repeat steps 3 – 13.
14 Press VHSj to engage the unit’s timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck
is automatically selected. Press A to turn off the unit. When
the HDD or DVD deck is in timer standby mode, the unit is
automatically turned off.
● To disengage the timer mode, press VHSj again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
^ anytime during steps 8 through 10, press number keys A9B for
weekly serials or number keys A8B for daily serials (Monday -
Friday).
Either AWEEKLYB or ADAILYB appears on the TV screen.
Pressing the button again makes the corresponding indication
disappear.
● You can programme this unit to timer-record as many as 8
programmes. If you try to programme the unit to record a ninth,
APROGRAM FULLB appears on the TV screen. To record the
extra programme, you must first cancel any unnecessary
programmes. (A pg. 56)
● In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 5 seconds.
● Programmes that start after midnight must have the next day’s
date.
● To record the programmes received by satellite receiver, record
on the HDD or the DVD discs. For details, refer to AManual Timer
ProgrammingB (A pg. 51).
VPS/PDC Recording
Now available from some TV stations, PDC (Programme Delivery
Control) and VPS (Video Programme System) are services
designed to assure safe, accurate timer recording. With this
system, special code signals are transmitted together with the
audio/video signals. These code signals control your video unit
and have precedence over the advertised times you may have
preset into the timer. This means that your unit will start and stop
recording when the preset TV programmes actually start and
end^even if the broadcast time of a preset TV programme is
changed.
NOTES:
● When you use Manual Timer Programming, set the start time
(VPS or PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
● VPS/PDC recording is not possible when a satellite receiver or a
cable system is connected to [L-2 IN/DECODER] connector on
your unit.
● VPS/PDC recording is also possible via the [L-1 IN/OUT]
connector.
Manual Timer Programming
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
rtwe
PROGRAMME
ENTER
0-9
REC MODE
VHS
VHS#
CABLE/SAT
DVDTV
[JK] N [ENTER]
[PROGRAMME] : EXIT
SHOWVIEW PRGM
NPROGRAMME/CONFIRM
PROGRAMME
DATE
START
STOP
[JK] N [ENTER]
[PROGRAMME] : EXIT
CH
CURSOR : [HI] SELECT : [JK]
CONFIRM : [ENTER]
DATE
START
DAILY/WEEKLY
TV PROG
STOP
SP/LP
SP
ARD
VPS/PDC
OFF
MON-FRI
MX1SEU_00.book Page 55 Monday, December 6, 2004 2:01 PM