Filter
Top Products
28
6-4 Alarm recording
6 RECORDING (contd.)
When an alarm signal is received (via the rear panel [ALARM IN] terminal) during recording, the alarm recording mode set with
the menu switch is automatically engaged.
1. Connect an alarm sensor.
Connect the alarm sensor to the rear panel [ALARM IN]
terminal.
2. Turn the power ON.
Check the connections and set the [POWER] switch on
the rear panel to ON.
3. Set the menu switches.
Set the required menu switches. For details, refer to
“Setting” on page 18.
Ⅵ [ALARM/SENSOR MODE]
⅙ [REC MODE] : Set to “ALARM”.
⅙ [REC DURATION] : Select how long you want alarm
recording to continue after an alarm signal is input.
Ⅵ [BUZZER]
⅙ [ALARM/SENSOR]: Set to “ON” to sound the buzzer
during alarm recording.
Reference: “5-3 Menu switch details” on page 21.
4. Start recording.
Refer to “Basic operation” on page 22.
When an alarm signal is received, alarm recording starts
(see step 3 above).
* To stop the buzzer during alarm recording, press the
[CANCEL] button.
Memo:
● Recording continues for about 5 seconds after the set
duration has passed.
● Alarm recording speed <REC SPEED> is fixed at “30”.
<AUDIO REC> is fixed to “ON”.
● <REC QUALITY> setting for alarm recording is the same as the
normal recording setting (used before an alarm is detected).
Repeat recording during alarm recording
ⅷ Repeat recording is canceled if even one alarm
recording is performed when menu switch
<REPEAT REC> is set to “AL·STOP”.
ⅷ When menu switch <REPEAT REC> is set to
“AL·LOCK”, alarm recorded sections are protected
when repeat recording is executed.
ⅷ When menu switch <REPEAT REC> is set to
“ALL”, all alarm recordings are overwritten except
Alarm 1.
ⅷ To erase Alarm 1, erase all alarms with the
[CLEAR] button.
ⅷ If the <REC DURATION> switch in <ALARM/
SENSOR MODE> is set to “MANUAL” and alarm
recording continues, recording will stop when the
disk is full even if menu switch <REPEAT REC> is
set to “ALL”.
POWER
WARNING
SLEEP
REC STOP PLAY STILL
TIMER CANCEL
DISPLAY
MENU
SEARCH
S
E
L
E
C
T
REV FWD
EXECUTE
SKIP/ALARM
SEARCH
REC
CLOCK RESET/ CLEAR
OPE. LOCK
ON
DIGITALVIDEORECORDER VR-510U
[MENU] button
Jog dial
Shuttle search dial
[CANCEL] button
[REC] button
When set to “ALL”
Beginning of the hard disk
Overwriting
Alarm 1
Alarm 2
Alarm 3
Alarm 4
Alarm 5
Repeat recording
End of the hard disk
[
EXT MODE
]
REC DUR
A
TION
10SEC
1.REC
MODE OFF
1.REC
MODE ARM
2.REC
DURAT ONI
2.HDD
FULL OUT OFF
[
ALARM SENSOR MODE]
180
AL
SEC
3.PRES
E
N
SO
R
4.PRES
E
N
SO
R
R
E
COFF
OGJ
[ALARM/SENSOR] screen
Set to “ALARM”.
3.
When set to “AL•LOCK”
Beginning of the hard disk
Alarm 1
Normal
recording 1
Alarm 2
Alarm 3
Normal
recording 2
Normal
recording 3
Normal
recording 1
Normal
recording 2
Normal
recording 3
End of the hard disk
Protected
Over-
writing
PROGRAM TIMER REC ALARM REC
<REC QUALITY>BASIC Recording with <REC
QUALITY> set to "BASIC"
Alarm detection
Before alarm detection
Repeat
recording