Filter
Top Products
64
RQT9274
Additional connections
≥To enjoy multi-channel surround sound DVD-Video, connect an
amplifier with Dolby Digital, DTS and MPEG decoders.
“Digital Audio Output” in the Setup menu (> 59)
≥When this unit is connected to an amplifier with an optical digital
audio cable and connected to a television with an HDMI cable, you
can enjoy the highest quality of audio from the disc by setting
“Digital Audio Output” to “Optical Only” in the Setup menu (> 60).
In this case audio is only output from the amplifier not the
television.
≥Before purchasing an optical digital audio cable (not included),
check the terminal shape of the connected equipment.
≥You cannot use DTS Digital Surround decoders not suited to DVD.
≥Connect to terminals of the same colour.
≥Supplied Audio/Video cable can also be used as an alternative for
Audio cable without connecting the video connector (yellow).
When connected to an HDMI compatible unit, an uncompressed digital audio and video signal is transmitted. You can enjoy high quality, digital
video and audio with just one cord. When connecting to an HDMI-compatible HDTV (High Definition Television), the output can be switched to
1080p, 1080i or 720p HD video.
≥Video sources converted to 1920k1080 resolution, while of high quality, will exhibit somewhat lower subjective image resolution than true,
native 1080p full-HD sources. See dealer for details.
≥Please use High Speed HDMI cables that have the HDMI logo (as shown on the cover).
≥When setting video output to “1080p”, please use the HDMI cables 5.0 meters or less.
≥If you are connecting to a TV that is only compatible with 2 channel audio output, audio with 3 channels or more will be down mixed (> 78) and
output as 2 channels, even if connecting with an HDMI cable. (Some discs cannot be down mixed.)
≥You cannot connect this unit to DVI devices that are incompatible with HDCP.
For units compatible with HDCP (High-Bandwidth Digital Content Protection) copyright protection that are equipped with a digital DVI input
terminal (PC monitors, etc.):
Depending on the unit, images may not be displayed properly or at all when connecting with a DVI/HDMI switching cable. (Audio cannot be
output.)
Connecting an amplifier with a digital
input terminal
Required setting
OUT
AV2
(
EXT
)
A V 1
(
TV
)
OPTICAL
DIGI DIGI T T AL AL A A UDIO OU UDIO OU T T
(PCM/BITSTREAM) (PCM/BITSTREAM)
COMPONENT COMPONENT
VIDEO OUT VIDEO OUT
P R
P B
Y
OUTOUT AA V4IV4 I NN
OPTICAL IN
Optical digital audio cable
Do not bend sharply when
connecting.
This unit’s rear panel
Insert fully, with
this side facing
up.
Amplifier’s rear panel
Connecting a stereo amplifier
S-VIDEOVIDEO
R- A UDIO- L
OUT OUT A A V4 I V4 I N N
AUDIO IN
R L
Audio cable
This unit’s rear panel
Amplifier’s rear panel
Connecting with an HDMI compatible television and receiver
Regarding VIERA Link “HDAVI Control
TM
” function
When connecting with a Panasonic TV (VIERA) or a receiver equipped with the “HDAVI Control” function, linked operations would be
possible. [> 34, Linked operations with the TV (VIERA Link “HDAVI Control
TM
”)]
≥Non-HDMI-compliant cables cannot be utilised.
≥It is recommended that you use Panasonic’s HDMI cable.
Recommended part number:
RP-CDHG10 (1.0 m), RP-CDHG15 (1.5 m), RP-CDHG20 (2.0 m), RP-CDHG30 (3.0 m), RP-CDHG50 (5.0 m), etc.
RF RF
IN IN
RF RF
OUT OUT
AV2
(
EXT
)
A V 1
(
TV
)
OPTICAL
DIGI DIGI T T AL AL A A UDIO OU UDIO OU T T
(PCM/BITSTREAM) (PCM/BITSTREAM)
COMPONENT COMPONENT
VIDEO OUT VIDEO OUT
P R
P B
Y
A A V OU V OU T T
S-VIDEOVIDEO
R- A UDIO- L
OUT OUT A A V4 I V4 I N N
HDMI AV OUT
HDMI IN
HDMI IN
HDMI OUT
HDMI cable
HDMI cable
Television’s rear panel
Receiver’s rear
panel
≥Set “Digital Audio Output” to “HDMI
and Optical” (> 60).
(The default setting is “HDMI and
Optical”.)
Required setting
This unit’s rear panel
Note
EH59GN-RQT9274-L_eng.book 64 ページ ２００９年２月１６日 月曜日 午後６時４９分