Philips 26PFL4907 Flat Panel Television User Manual


  Open as PDF
of 67
 
English
13
These operations are accessible by remote control.
Some may also be accessible by control panel on the main unit.
Initialsetup
This section will guide you through the unit’s initial setting which
includes selecting a language for your on-screen menu, country, location
and AutoProgram, which automatically scans and memorizes viewable
channels. You can also set the network connection in this setting.
Before you begin:
Make sure the unit is connected to antenna or cable.
1 After making all the necessary connections, press to Turn On the
unit.
• It may take a few moments to Turn On the unit for the rst time.
• Initial setup menu appears automatically after the unit is Turned
On.
2 Use ▲▼ to select the on-screen language, country, location on the
right side of the TV screen, then press OK.
• You must set Home in location setting. Otherwise, Picture and
Sound settings you adjusted will not be memorized after the unit
goes into Standby mode.
3 Use ▲▼ to select the signal type.
• If the TV is connect to a cable box or satellite set-top box, select
the 2nd one and skip to step 5.
TosetupaTVsignalfromacableTV
walljackorastandardTVantenna.
Select
TosetupaTVsignalfromacableTV
boxorsatelliteTVreceiver.
Select
4 Use ▲▼ to select Antenna for TV channels or Cable for CATV
channels, then press OK.
Makesurethatyouhave
attachedyourantennaorcable
signalintothejackontheback
ofyourTVlabeled“ANTENNA.IN”.
NowselecteitherAntennaor
Cable,usingup/downkeyofthe
remotecontrol.Onceyouhave
madeyouselection,pressthe
OKbuttontoproceed.
Antenna
Cable
Skip
– When Antenna is selected, the TV detects antenna signals. It searches
for DTV and Analog TV channels available in your area.
– When Cable is selected, the TV detects signals supplied by cable. It
searches for DTV, Analog TV and Cable channels available in your
area.
• Autoprogram will begin.
Systemsearching.Pleasewait...
Digitalchannelsfound: 0
Analogchannelsfound: 0
Autoprogrammingmaytakemorethan20minutesto
complete.DigitalchannelswilltakelongerthanAnalog
tofindandprogram.Pleasewaituntilyousee
theAutoProgrammingcompletemessage.
Stop
5 After the channel installation is completed, Network setup screen
will appear. Use ▲▼ to select Wireless or Wired, then press OK.
ThisTVcanbeconnectedto
yourhomenetwork.
Selectyourconnectiontype.
Wireless
Wired
Skip
Wireless
If you have a router with WPS function, select
Wireless to connect to the Internet.
Wired
If you connect with an Ethernet cable, select
Wired to connect to the Internet.
• If you select Wireless, use ▲▼ to select EasyConnect and
press OK.
6 Follow the on-screen instructions to complete the installation.
• When you select On in the selection screen of
Autosoftwareupdate. A message will appear if there is the
latest software on the network server.
7 Use ◄► to select Start,thenpress OK to begin Settingsassistant.
Settingsassistantwillallowyoutocustomizeyourpicturesettingstoyour
personalpreference.Youwillseeaseriesoftestpictureswhere
therightsideandleftsidediffer.Selectthesidethatismostpleasingto
youwiththeLeft/Rightbuttons.
Cancel Start
8 Press ◄
or ►
5 times to select the side of the pictures that is the
most pleasing to you, then press OK.
Whichsideofthepicturedoyouprefer?
Cancel Picture A Picture B
Continued on next page.
 previous next