Filter
Top Products
12
ADDITIONAL CONNECTIONS EXAMPLES
Connecting to a TV with an EURO-AV cable
Please follow these steps before turning on the power.
1. If your TV has an EURO-AV socket, connect the unit as shown in
Fig. 10. (Do not connect the video lead to the MONITOR OUT VIDEO
socket.) You can enjoy high quality picture playback.
2. Set the VIDEO OUT SELECT switch to RGB.
Connecting to a TV with an S-video lead
Please follow these steps before turning on the power.
1. If your TV has an S-video input socket, connect the unit as shown in
Fig. 11. (The MONITOR OUT VIDEO socket connection is not
necessary.) You can enjoy clearer picture playback.
2. Set the VIDEO OUT SELECT switch to S-VIDEO.
TV or Audio equipment connections (Fig. 12)
Connect an audio lead between the VIDEO (AUDIO) IN sockets of the unit
and the audio output sockets of the TV or audio equipment.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of Digital
Theater Systems, Inc.
SYSTEM CONNECTIONS EXAMPLES
JCX-TS760/JCX-TS762, TV and Video equipment
(Fig. 13)
JCX-TS760/JCX-TS762, TV and VCR (Fig. 14)
JCX-TS760/JCX-TS762, TV, VCR and Audio
equipment (Fig. 15)
JCX-TS760/JCX-TS762, TV, VCR, STB and Audio
equipment (Fig. 16)
BEFORE OPERATION
This instruction manual explains the various
functions of this unit using the remote control.
The buttons on the main unit perform similar functions to similarly
marked buttons on the remote control.
Turning the power on and off
Press the z/ON button. “HELLO” appears briefly on the display. (After
connecting the mains lead, when you press the z/ON button for the first
time, the volume-reset feature automatically sets the initial volume level.)
To turn the power off, press the z/ON button again. “GOOD-BYE” appears
briefly.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the unit
turns on automatically and the selected function is activated.
Remote control a (Play), TUNE/BAND, OPEN/CLOSE
Main unit a, q
Selecting the function
Press the FUNCTION button to select the desired function. Each time the
button is pressed, the display changes as follows:
DVD/CD
v
TV
v
VIDEO
v
FM TUNER
v
AM TUNER
v
. . .
- When the function selection is changed, disc play is automatically
stopped.
Adjusting the volume
Press the “+” or “–” VOLUME button (or turn the VOLUME control on the
main unit). The volume level appears on the display (VOL 0 ~ VOL MAX).
To reduce the volume temporarily
Press the MUTE button. “MUTE” blinks on the display. To restore the
previous volume setting, press the MUTE button again.
Selecting the sound mode
1. Press the SOUND button repeatedly to select the desired sound mode
(“BASS”, “TREBLE”, “CINE”:Cinema or “QS”:Q-Surround).
2. Press the button as desired.
Sound mode Press Display change
BASS 4 or 5 “+5” ~ “–5”
TREBLE 4 or 5 “+5” ~ “–5”
CINE ENTER “ON” or “OFF”
QS ENTER “LOW” or “HI”
Note for “CINE”:
When enjoying a DVD disc with the volume set low at night, select this
mode. It enhances spoken lines making speech clearer.
3. Repeat steps 1 - 2 for another sound mode.
4. Press the SOUND button repeatedly to close the display.
Bass boost system
Press the BASS button to select the desired bass boost effect.
BOOST
v
BASS OFF
v
NORMAL . . .
Adjusting the display brightness
While pressing the n button on the main unit, press the ON SCREEN
button on the remote control.
DIMMER 1
v
DIMMER 2
v
DIMMER 0 . . .