Filter
Top Products
280-8207-00
VRX756VD 25
English
Owner’s manual
Basic Operations
Adjusting the AUDIO
Note:
• When the separately-sold 5.1 ch Surround
Decoder (DVH940) is used, the bass and treble
tone adjustments cannot be made. To adjust the
tone, refer to the section “5.1 ch Surround
Decorder Operations”.
Adjusting the balance/fader
1. Press the [ADJ] button, then touch the
[AUDIO] key.
2. Touch the [BAL/FAD] key.
3. Touch the [w] or [z] key to adjust to the
fader level.
∗ The factory default setting is “0”. (Adjustment
range: front 13 to rear 13)
[w] key: Emphasized the sound from the
front speakers.
[z] key: Emphasized the sound from the
rear speakers.
4. Touch the [Å] or [Î] key to adjust to the
balance level.
∗ The factory default setting is “0”. (Adjustment
range: left 12 to right 12)
[Å] key : Emphasized the sound from the left
speakers.
[Î] key : Emphasized the sound from the
right speakers.
5. Touch the [RTN] key, [ESC] key, or press the
[ADJ] button.
Adjusting the BASS
The bass gain, bass frequency (center frequency)
and bass Q can be adjusted as follows.
1. Press the [ADJ] button, then touch the
[AUDIO] key.
2. Touch the [BASS] key.
3. When the bass type selection screen is
displayed, touch the key for the desirable
type to select it.
4. Touch the [w] or [z] key to adjust to
desirable level.
GAIN : –6 to 8 (The factory default setting
is “0”)
FREQ. : 50Hz/80Hz/120Hz (The factory
default setting is “50”)
Q:1/1.25/1.5/2 (The factory default
setting is “1”)
5. Touch the [RTN] key, [ESC] key, or press the
[ADJ] button.
Housing the liquid crystal panel
1. Press the [OPEN] button and the liquid
crystal panel is housed automatically.
Note:
• When leaving this unit unused for a long period of
time or leaving your car, be sure to house the
liquid crystal panel into the main unit.
Turning the liquid crystal panel
horizontal (Air conditioner
operation mode)
When the way the liquid crystal panel is
mounted hinders the operation of the air
conditioner, the position of the panel can be
turned horizontal temporarily.
1. Press and hold the [OPEN] button when the
liquid crystal panel is upright, and release
the button when a beep is heard.
2. The liquid crystal panel turns horizontal.
∗ Press the [OPEN] button again when the liquid
crystal panel is in the horizontal position, and
the panel returns to the original position.
∗ The unit can also be set so that the panel
returns to its original angle after a set time in
the horizontal position (See P. 28).
Mute
1. When in the radio, VISUAL or TV mode, each
time you press the [MUTE] button, mute is
turned on and off. “MUTE” appears when
mute is turned on.
2. In modes other than radio, VISUAL, or TV,
enable the MUTE function by holding the
[MUTE] button depressed for 1 second or
longer.
Regarding the menu screen’s [RTN]
and [ESC] keys
•[RTN]: Touch the [RTN] key to return to the
previous screen.
•[ESC]: Touch the [ESC] key to return to the
main screen.
In the ADJUST MODE, pressing the [ADJ]
button will also cause a return to the main
screen.
In cases where this kind of multiple key
response is supported, the following kind of
notation will be used:
Touch the [RTN] key, [ESC] key, or press the
[ADJ] button.
+VRX756VD-009-Eng1 05.1.18, 0:59 PM25