Filter
Top Products
49
■ DTS Out
This player is capable of outputting DTS digital audio for DVDs
recorded in DTS. If this player is connected to an AV
component that has a built-in DTS decoder, select [DTS]. If
your system is not equipped to decode DTS, select [DTS 3
PCM]. Refer to the operating instructions supplied with your
audio components if you are unsure about compatibility with
DTS.
—
—
—
—
—
—
V2Video1
General
A2
Language
Exit
Move
Audio DRC
Dolby Digital Out
DTS Out
Linear PCM Out
MPEG Out
Digital Out
SACD Playback
Audio1
Off
Dolby Digital
DTS
DTS3 PCM
MPEG 3 PCM
On
2ch Area
SETUP
—
—
—
—
—
—
V2Video1
General
A2
Language
Exit
Move
Audio DRC
Dolby Digital Out
DTS Out
Linear PCM Out
MPEG Out
Digital Out
SACD Playback
Audio1
Off
Dolby Digital
DTS 3 PCM
Down Sample On
Down Sample Off
On
2ch Area
SETUP
■ MPEG Out
This player is capable of outputting the MPEG digital
bitstream. If the player is connected to an AV component that
has a built-in MPEG decoder, select the [MPEG] setting.
Otherwise, select [MPEG 3 PCM] to convert the digital signal
to the PCM signal, (the digital signal output from a CD).
—
—
—
—
—
V2Video1
General
A2
Language
Exit
Move
Audio DRC
Dolby Digital Out
DTS Out
Linear PCM Out
MPEG Out
Digital Out
SACD Playback
Audio1
Off
Dolby Digital
DTS 3 PCM
Down Sample On
MPEG
MPEG 3 PCM
2ch Area
SETUP
—
—
—
—
—
V2Video1
General
A2
Language
Exit
Move
Audio DRC
Dolby Digital Out
DTS Out
Linear PCM Out
MPEG Out
Digital Out
SACD Playback
Audio1
Off
Dolby Digital
DTS 3 PCM
Down Sample On
MPEG 3 PCM
On
Off
SETUP
Settings: DTS
DTS 3 PCM (Factory setting)
Note
If you have made digital audio connections to component(s) not
equipped to decode the DTS digital bitstream, be sure to select [DTS
3 PCM]. DTS signals are converted to Linear PCM signals then
output. If a DTS signal is output without decoding, the output is
digital noise that could potentially cause damage to your speakers.
Settings: Down Sample On (Factory setting)
Down Sample Off
Notes
• On DVDs that contain copy protection, the 96 kHz signal may
only be output from the analog audio jacks.
• Even when set to [Down Sample Off], some discs will be down
mixed to 48 kHz/44.1 kHz and not output digitally.
• High sampling rate DVD audio discs (192 kHz or 176.4 kHz)
always output audio down sampled to 96 kHz or 88.2 kHz through
digital outputs.
Settings: MPEG
MPEG 3 PCM (Factory setting)
■ Linear PCM Out
If your AV amplifier (or other connected component) is
compatible with high sampling rates (96 kHz), set this to
[Down Sample Off], otherwise set it to [Down Sample On]
(96 kHz audio is converted to a more compatible 48 kHz/
44.1kHz). Check the manual that came with the other
component if you’re unsure whether it is 96 kHz compatible.
■ Digital Out
Expert
Depending on your preferences and the type of connections
made, you may opt not to have the digital audio signal output
at all. When this setting is set to [Off] there is no signal output
from the digital audio output jacks.
Make changes to the [Digital Out] setting in the Setup screen
Audio menu in the [Expert] menu mode (page 47).
Note
• DVD audio does not allow for downmixing. In this case, digital
audio will not be output.
Settings: On (Factory setting)
Off
Note
You cannot output SACD audio digitally.
DPS8.3.E.46-64.p65 02.9.12, 11:46 AM49