Filter
Top Products
8 EN
INITIAL SETTINGS
Clock
ATTENTION CABLE BOX SUBSCRIBERS
If you perform the Advanced Auto Clock Set procedure . . .
● Select the PBS channel on your cable box before plugging
your VCR’s power plug into the AC outlet. (If you have
more than one PBS channel, you may have to select an
alternative PBS channel if Advanced Auto Clock Set is not
successful.)
● If there is no PBS channel in your area, perform the
Manual Clock Set procedure (੬ pg. 11).
● For automatic clock adjustment to take place the VCR's
power must be off and the cable box must be set to the
PBS channel at clock adjustment times.
● If you perform Advanced Auto Clock Set successfully,
D.S.T. will be set to “AUTO”. At the D.S.T. adjustment time
(੬ pg. 11), your VCR's power must be off and your cable
box must be set to the host PBS channel in your area for the
D.S.T. adjustment to take place. If the clock is not set
correctly, change the D.S.T. setting to “ON” or “OFF”. See
step 9 of Semi-Auto procedure (੬ pg. 10) or step 6 of
Manual procedure (੬ pg. 11).
8
Advanced Auto Clock Set
Your VCR can automatically set its clock when the power plug is
first connected to an AC outlet.
To set the clock automatically:
1. Connect the cable or antenna cable to your VCR.
2. Connect the VCR's power plug to the AC outlet.
3. "AUTO" is displayed on the VCR's front panel to show that the
clock is being set automatically.
4. Do not power on the VCR until the clock or "--:--" is displayed
on the VCR's front display panel.
The time and date can be set automatically from clock setting data
that is transmitted by one of the regular TV broadcast channels. We
call this TV channel the "Host Channel" and it is a PBS channel in
your area. The Advanced Auto Clock Set function scans all the
channels received by your VCR to find the Host Channel and then
sets the clock.
NOT SET
PM
SET
Before the clock is set, AUTO blinks on the display.
After setting, the current time appears (in hours and minutes).
The Advanced Auto Clock Set function will normally set the
clock correctly. However, if an incorrect time is displayed on
the front display panel, you may be receiving the clock setting
data of a PBS channel from an adjacent time zone, or an
incorrect PBS channel from a cable TV system. In this case,
perform the Semi-Auto (੬ pg. 10) or Manual (੬ pg. 11) clock
setting procedure.
If "AUTO CLOCK SET" or "SEMI-AUTO CLOCK SET" is selected
at the Override Auto Clock Set screen on page 10, the clock
will be adjusted automatically by the Host PBS every hour on
the hour (except for 11:00 PM, midnight, 1:00 AM and 2:00
AM) by the incoming PBS channel clock setting data. (This
automatic clock adjustment can only be performed when the
VCR’s power is turned off. The clock will be adjusted on the
hour based on the time displayed on the VCR, not on the actual
real time.) The default setting is "AUTO CLOCK SET".
If “- - : - - ” appears on the display, your antenna cable may not
be connected to the VCR, there may not be a Host PBS signal
available in your area, or your cable box may not be set to the
PBS channel. Ensure that the antenna cable is connected
correctly. If you use a cable box ensure that your local PBS
channel is selected on your cable box (
੬ ATTENTION CABLE
BOX SUBSCRIBERS). Then power on and power off the VCR,
the Advanced Auto Clock Set mode will be automatically
reactivated and "Auto" will be displayed on the VCR's front
panel. If Advanced Auto Clock Set is not performed but
everything is connected and set correctly, perform the Manual
Clock Set procedure (੬ pg. 11).
NOTE:
If the memory backup fails, because of a power outage or because
the AC was removed from the VCR, Advanced Auto Clock Set
will be performed when power is restored to the VCR.