Filter
Top Products
Masterpage:Right-No-Heading
61
Filename [XVS20EK_09Editing.fm]
Page 61 March 28, 2003 6:55 pm
Edit To Or From
Another Video
Recorder
You can use your unit as the source player or as the
recording deck.
A
Make connections.
Connect the player’s 21-pin SCART connector to the
unit’s 21-pin SCART connector as illustrated.
A
When using your unit as the source player:
— connect its L-1 IN/OUT connector to the recording
deck.
B
When using your unit as the recording deck:
— connect its L-1 IN/OUT or L-2 IN/DECODER
connector to the source player.
●
If another recorder is compatible with the Y/C signal:
— when using your unit as the source player, set “L-1
OUTPUT” to “S-VIDEO”. (
੬
pg. 62)
— when using your unit as the recording deck, set “L-2
INPUT” to “S-VIDEO”. (
੬
pg. 63)
B
Select the S-VHS deck.
On the unit
Press
S-VHS/DVD
repeatedly so that the S-VHS indicator
lights up.
On the remote control
Press
S-VHS
so that the S-VHS indicator lights up.
C
Set the input mode of recording deck.
With this unit, press
AUX
(
number key “0”
) and/or
PR
to
select “L-1” for the L-1 IN/OUT connector, or “L-2” for
the L-2 IN/DECODER connector, depending on the
connector being used.
●
When using another recorder as the recording deck, refer to its
instruction manual.
●
When using the L-2 IN/DECODER connector, set “L-2
SELECT” to “A/V”. (
੬
pg. 63)
D
Set the edit mode.
See “PICTURE CONTROL” on page 71.
E
Start the source player.
Engage the Play mode of the source player.
F
Start the recording deck.
Engage the Record mode of the recording deck.
NOTES:
●
All necessary cables can be obtained from your dealer.
●
For Y/C signal input/output, be sure to use a 21-pin SCART
cable that is compatible with the Y/C signal.
●
When you select “EDIT” to dub tapes in step
D
, be sure to
select “AUTO” (or “NORM” when “B.E.S.T.” is set to “OFF”)
after you finish dubbing the tapes.
●
When you use this unit as the source player for editing, be sure
to set “O.S.D.” to “OFF” before starting. (
੬
pg. 72)
●
If you are using another recorder with S-Video and Audio
output connectors, connect its S-Video and Audio output
connectors to this unit’s front panel S-VIDEO and AUDIO
input connectors. Then, set the unit’s input mode to “S-1” in
step
C
.
Advantages of S-VHS video recorders
You can edit from VHS to S-VHS, S-VHS to VHS, or, from
S-VHS to S-VHS.
●
From VHS to S-VHS: Record VHS playback signals in the
S-VHS mode. Although the picture quality is inherently
limited by that of the original, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
●
From S-VHS to VHS: Because the picture quality of the
source material is very high, the edited tape has better
picture quality than those made by VHS-to-VHS editing.
●
From S-VHS to S-VHS: All signals will be transferred with
minimum degradation.
A
B
AV mode
21-pin SCART cable
(not provided)
Recorder
Your unit
Another recorder
Player
TV receiver
AV mode
21-pin SCART cable
(not provided)
Recorder
Your unit
Another recorder
Player
TV receiver
Slide the
TV/S-VHS/DVD
switch to the right.
XVS20EK_01.book Page 61 Friday, March 28, 2003 7:00 PM