Filter
Top Products
60
9. O.S.D Message
No. O.S.D Message Meanings
1 NO DISK
No hard-disk detected after power activated
2 BATTERY LOW
Suggest change the battery and reset the system time
3 LOADING
System Boot up
4 VIDEO LOSS
Video loss
5 VIDEO IN
Video input source
6 KEY LOCKED
Key lock function is on
7 KEY UNLOCKED
Key lock function is off
8 n1 OF n2 ITEMS PROGRESS n3 %
BACKUP n1/n2 NOW n3 %
9 BACKUP COMPLETE
Backup complete
10 HD2 SPACE NOT ENOUGH
HD2 has not enough space for backup
11 NO RECORD FOR BACKUP
No backup is possible.
12 BACKUP INCOMPLETE
Backup incomplete, since the user has pressed the STOP
button to stop it
13 NOT FOUND
The system cannot find a video in the Search function.
14 END
Playback of recorded video has reached the end point
15 DISK FULL
Hard-disks are full; this happens only when the DISK FULL
item in the setup menu is set to STOP.
16 EMPTY
The user presses the PLAY button or uses the SEARCH
function, but no video can be played.
17 SET TO NTSC, PLS RESTART
System has to be set to NTSC, please reboot (PAL is similar)
18 SOFTWARE UPDATE
Software update
19 PLEASE RESTART
The system should be rebooted after the software has been
updated
20 NO DISK
The user has pressed the Save key without putting in a SD
card, or there is a disk error.
21 DATA NOT CONTINUOUS
The system finds data in installed HDs cannot be used
contiguously. Suggest you remove HD2 from the system.
22 DISK ATTACHED
HD2 has been attached.
23 DISK REMOVED
HD2 has been removed.
24 FAN STOPPED
The chassis fan has stopped for over 30 seconds.
25 HDn ERROR AT xxxxx
There is a hard-disk error during recording, where n is the
hard-disk number and xxxxx is the hexadecimal location.
26 NOT PRESENT
When the user tries to clear a disk that was not attached in
the setup menu.
27 SAVE TO DISK
Start saving to the JPEG file.
28 SAVE TO Fnnn. JPG
Save to Fnnn. JPG (where nnn= 0..999)
29 SAVE OK
Save to the JEPG is ok.
30 SD CARD WRITE PROTECT
A SD card is write-protected; or there is an error
31 WAIT . . .
The composition of the hard-disk is changing now. Or, it is
saving the image into the SD card. Please wait for a while.
61
10. Network Viewer and Image Viewer
This section provides instructions for installing and using the Network Viewer, and Image Viewer,
which are included with the VR-601. The programs can be operated by a selected PC equipped with
the following requirements.
1. Intel Pentium 233MHz at least.
2. 32 MB RAM
3. Window 95, 98, NT, ME, 2000 and XP.
4. 4 MB Video card capable of 24-bit true color display.
5. 5 MB free hard-disk space for software installation.
6. 10-base T network for LAN operation.
10.1 The Network Viewer
10.1.1 Introduction to Network Viewer
The Network Viewer allows you to potentially access 16 units of the VR-601 from a remote
desktop or a laptop in a TCP/IP networking environment. It can perform the following functions.
z View live images from the VR-601
z Store, search, and review recorded video from the VR-601 HDD.
z Change the regular record, event record, and timer properties.
Before you are ready to view images from a desktop, you need to have your VR-601 networked
by obtaining a 10 base Ethernet data cable (Standard RJ-45) to connect the VR-601 to your
LAN/WAN. Now enter the main menu to set the IP address.
RJ-45 PIN configuration for Ethernet
PIN NO. PIN Assignment
1.
TX +
2.
TX -
3.
RX +
4.
Not Connected
5.
Not Connected
6.
RX -
7.
Not Connected
8.
Not Connected
VR-601
PC
RJ-45
1 2 3 4 5 6 7 8
RJ-45 socke
t