Samsung 760 Series Flat Panel Television User Manual


  Open as PDF
of 282
 
English - 128
Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1
Press the TOOLS button.
Press the ENTER button to select Anynet+ (HDMI-CEC).
2 Pressthe▲or▼buttontoselect Receiver.
Pressthe◄or►buttontoselect
On or Off.
3 Press the EXIT button to exit.
➢
If your receiver supports audio only, it may not appear in the device list.
➢
The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of
the TV.
➢
When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is
displaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is
a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the
Home Theater receiver.
➢
When using the WISELINK Pro feature, sound may not output properly through the receiver.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related(MTS, Preferred
language) menus.
➢
If there is a power interruption to the TV when the Receiver is set to On (by disconnecting the power cord or a power
failure), the Select Speaker may be set to External Speaker when you turn the TV on again. (see page 32)
Troubleshooting for Anynet
+
Symptom Solution
Anynet
+
does not work. ■ CheckifthedeviceisanAnynet
+
device. The Anynet
+
system supports Anynet
+
devices
only.
■ Connectonlyonereceiver(hometheater).
■ CheckiftheAnynet
+
device power cord is properly connected.
■ ChecktheAnynet
+
device’s Video/Audio/HDMI 1.3 cable connections.
■ CheckwhetherAnynet+(HDMI-CEC)issettoOnintheAnynet+setupmenu.
■ CheckwhethertheTVremotecontrolisinTVmode.
■ CheckwhetheritisAnynet+exclusiveremotecontrol.
■ Anynet+doesn’tworkincertainsituations.(Searchingchannels,OperatingWISELINK)
■ When connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or your TV off and on again.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet
+
. ■ CheckiftheAnynet
+
device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet
+
Setup menu.
■ PresstheTV button on the TV remote control to switch to TV. Then press the TOOLS
button to show the Anynet
+
menu and select a menu you want.
I want to exit Anynet
+
. ■ SelectView TV in the Anynet
+
menu.
■ PresstheSOURCE button on the TV remote control and select a device other than Anynet
+
menu.
■ PressCH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.
(Note that the channel button operates only when an Anynet
+
device with a built-in tuner is
not connected.)
The message Connecting to
Anynet
+
device... appears on the
screen.
■ YoucannotusetheremotecontrolwhenyouareconfiguringAnynet
+
or switching to a view
mode.
■ UsetheremotecontrolwhentheAnynet
+
setting or switching to view mode is complete.
The Anynet
+
device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ CheckwhetherornotthedevicesupportsAnynet
+
functions.
■ CheckwhetherornottheHDMI1.3cableisproperlyconnected.
■ CheckwhetherAnynet+(HDMI-CEC)issettoOnintheAnynet+setupmenu.
■ SearchAnynet+devicesagain.
■ YoucanconnectanAnynet
+
device using the HDMI 1.3 cable only. Some HDMI cables may
not support Anynet
+
functions.
The TV program cannot be
recorded.
Check whether the antenna jack on the recording device is properly connected.
The TV sound is not output through
the receiver.
Connect the optical cable between TV and the receiver.
ReturnAdjust
Move
View TV
Device List
Recording : DVDR
DVDR Operation
Receiver ◄On►
Setup
BN68-01653A-Eng.indb 128 2008-08-27 오후 5:13:03
 previous next