FUNAI DVR90VG DVD VCR Combo User Manual


 
10
EN
Functional overview (cont’d)
Before you start
Using a remote control
Keep in mind the following when using the remote
control:
Make sure that there is no obstacle between the
remote control and the remote sensor of the unit.
Remote operation may become unreliable if
strong sunlight or fluorescent light is on the
remote sensor of the unit.
Remote control for different devices can interfere
with each other. Avoid using remote control for
other equipment located close to the unit.
Replace the batteries when you notice a fall-off of
the operating range of the remote control.
The maximum operable ranges from the unit are
as follows.
-
Line of sight: approx. 23 feet (7m)
- Either side of the center:
approx. 16 feet (5m) within 30°
-
Above: approx. 16 feet (5m) within 15°
-
Below: approx. 10 feet (3m) within 30°
Installing batteries in the remote
control
Install two “AA” size batteries (supplied), matching
their polarity to those indicated inside battery
compartment of the remote control.
2
1
3
Note:
Incorrect use of batteries can result in hazards such
as leakage and bursting. Please follow the instruction
below:
Do not mix new and old batteries together.
Do not use different kinds of batteries together.
Although they may look similar, different batteries
may have different voltages.
Make sure that the plus and minus ends of
each battery match the indications in the battery
compartment.
Remove batteries from equipment that is not going
to be used for a month or more.
When disposing used batteries, please comply
with governmental regulations or public rules for
environmental protection that apply in your country
or area.
Do not recharge, short-circuit, heat, burn or
disassemble batteries.
2
1
3
2
1
3
Because this product is a combination of a VCR and a DVD recorder, you must select first which component
you wish to operate with [OUTPUT SELECT].
DUBBING
OPEN/CLOSE
POWER REW F.FWD PLAY
VCR
VCR
OUTPUT SELECT
DVD
STOP PLAY
L
CHANNEL
K
RECORD
STOP/EJECT
DVD
VIDEO
RECORD
Bs
A
B BC
C ADE
S
-
VIDEO
L
-
AUDIO
-
R
VCR
OUTPUT SELECT
DVD
Bs
STOP
POWER
T-SET
TIMER PROG.
SKIP SKIP
OPEN/CLOSE
SPACE
1 2 3
4 5 6
7 8
0
9
CH
VIDEO/TV
SLOW
PAUSE
.@/:
ABC DEF
GHI JKL MNO
PQRS
REC/OTR
DISPLAY
TUV WXYZ
DVD
REC/OTR
REC SPEED
ZOOM
SEARCH
VCR
SETUP
CM SKIP
RETURN
MENU/LIST
TOP MENU
DUBBING
x1.3/0.8
CLEAR
ENTER
PLAY
AUDIO
OUTPUT SELECT button
DVD indicator
VCR indicator
DVD button
VCR button
Press [VCR ] on the remote control.
(Verify that the VCR indicator is lit.)
Press [DVD ] on the remote control.
(Verify that the DVD indicator is lit.)
The VCR / DVD recorder switching
Note:
Pressing only
[OUTPUT SELECT] on the front
panel DOES NOT switch the mode of the remote
control. You MUST select the correct mode on
the remote control.
You cannot switch to another mode (DVD or
VCR) during in the timer-standby mode.
Pressing
[REC/OTR] (DVD) or [REC/OTR] (VCR)
on the remote control switches immediately its
respective mode so that you can start recording
directly on the appropriate media.
D
U
B
B
I
N
G
O
P
E
N
/
C
L
O
S
E
P
O
W
E
R
R
E
W
F
.
F
W
D
P
L
A
Y
V
C
R
V
C
R
O
U
T
P
U
T
S
E
L
E
C
T
D
V
D
S
T
O
P
P
L
A
Y
R
E
P
E
A
T
T
R
K
.
D
V
D
L
C
H
A
N
N
E
L
K
R
E
C
O
R
D
ST
OP/EJECT
V
C
R
R
E
C
O
R
D
D
V
D
V
I
D
E
O
R
E
C
O
R
D
B
B
s
A
B
B
C
C
A
D
E
S
-
V
I
D
E
O
L
-
A
U
D
I
O
-
R
S
K
I
P
R
E
C
P
A
U
S
E
P
E
N
T
E
R
M
E
N
U
P
L
A
Y
L
I
S
T
T
O
P
M
E
N
U
/
O
R
I
G
I
N
A
L
k
K
F
W
D
g
S
T
O
P
C
P
L
A
Y
B
R
E
V
h
H
G
Remote
control
Within about
23feet (7m)
30°
30°
VCR MODE
DVD MODE
E9A10UD_DVR90VG.indd 10 2005/12/26 18:54:57