Filter
Top Products
Filename [MH200SEU_11Editing.fm]
Masterpage:Left+
64 EN
EDITING
Page 64 Wednesday, 25 May 2005 13:34
L-1 Output And L-1 Input Setting
The [L-1 IN/OUT] connector accepts and delivers either a composite
signal (regular video signal) or a Y/C signal (a signal in which the
luminance and chrominance signals are separated). Set
A
L-1 OUTPUT
B
and
A
L-1 INPUT
B
to the appropriate mode depending
on the type of appliance connected to the unit’s [L-1 IN/OUT]
connector.
1 Press SET UP to access the Main Menu screen.
2 Press selection keys to select AFUNCTION SET UPB, then
press G.
3 Press selection keys
to select AVIDEO IN/
OUTB, then press G.
4 Press selection keys
to select
AL-1 OUTPUTB or
AL-1 INPUTB, then
press ENTER.
5 Press selection keys
to select the
appropriate setting,
then press ENTER.
6 Press SET UP to
complete the setting.
\
*The boldface settings below indicate the settings at your purchase.
8 L-1 OUTPUT ^ SCART VIDEO / SCART S-VIDEO / SCART
RGB / COMPONENT
SCART VIDEO:
If a connected appliance’s input is compatible only with regular
video signals, set to ASCART VIDEOB
.
SCART S-VIDEO:
If a connected appliance’s input is compatible with Y/C signals,
set to ASCART S-VIDEOB. You can obtain high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
SCART RGB:
If a connected appliance’s input is compatible with RGB signals,
set to ASCART RGBB. You can obtain a high-quality RGB
picture.
COMPONENT:
If a connected appliance’s input is compatible with Y/P
B
/P
R
signals, set to ACOMPONENTB. You can obtain a high-quality Y/
P
B
/P
R
picture. Switch the TV to the input that you can watch
component video pictures.
8 L-1 INPUT ^ VIDEO / S-VIDEO
VIDEO:
If a connected appliance’s output is compatible only with regular
video signals, set to AVIDEOB.
S-VIDEO:
If a connected appliance’s output is compatible with Y/C
signals, set to AS-VIDEOB. You can obtain a high-quality picture.
(For connection, be sure to use a 21-pin SCART cable that is
compatible with the Y/C signal.)
NOTES:
● If AL-1 OUTPUTB is set to ASCART S-VIDEOB or ASCART RGBB, it
is not possible to set AL-1 INPUTB to AS-VIDEOB.
● If AL-2 SELECTB is set to ASAT S-VIDEOB or ADECODERB, it is not
possible to set AL-1 INPUTB to AS-VIDEOB.
● If AL-2 SELECTB is set to ADECODERB, it is only possible to set
AL-1 OUTPUTB to ASCART VIDEOB
.
● Component video signals are not output from the [L-1 IN/OUT]
connector.
● When Progressive scan mode is engaged, it is not possible to
select the setting of AL-1 OUTPUTB. (A pg. 64)
Output/Input Set
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/SAT/DVD switch to DVD.
ENTER
SET UP
FGDE
CABLE/SAT
DVDTV
Selection Keys
DVD VIDEO SET UP
MONITOR TYPE
HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
REC/PLAY SET UP
DISPLAY SET
F-1 INPUT
L-1 OUTPUT
L-1 INPUT
L-2 SELECT
VIDEO IN/OUT
4:3LB
VIDEO
SCART VIDEO
VIDEO
VIDEO
SELECT WITH @ THEN PRESS [ENTER]
ENTER
SELECT
SET UP
EXIT
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP
HDD/DVD SET UP FUNCTION SET UP
INITIAL SET UP
REC/PLAY SET UP DISPLAY SET
VIDEO IN/OUT
SELECT WITH @ THEN PRESS [ENTER]
ENTER
SELECT
SET UP
EXIT
PRESS [SET UP] TO EXIT
MONITOR TYPE
F-1 INPUT
L-1 OUTPUT
L-1 INPUT
L-2 SELECT
4:3LB
VIDEO
SCART VIDEO
VIDEO
VIDEO
SCART VIDEO
SCART S-VIDEO
SCART RGB
COMPONENT
MH200SEU_00.book Page 64 Wednesday, May 25, 2005 1:34 PM