Filter
Top Products
EN 43
Set tape speed
Press SP/EP ( ) to set the tape speed.
Return to normal screen
Press PROG. or OK.
“PROGRAM COMPLETED” appears on the
screen for about 5 seconds, then normal screen
appears.
• If “PROGRAM NOT COMPLETED PROGRAM
OVERLAP” appears, you have another program
overlapping the program you have just made.
The Program Check screen appears and
conflicting programs will start blinking.
You can now correct the conflicting programs.
See “When programs overlap each other” on
page 45.
Engage timer recording standby mode
Press TIMER.
The VCR turns off automatically and “‰” is
displayed on the front display panel.
To timer-record daily (Monday–Friday) or weekly
serials
Press DAILY (M-F) (number “8”) or WEEKLY (number
“9”) anytime during steps through .
“DAILY” or “WEEKLY” appears on the Program screen.
● Pressing the button again makes the corresponding
indication disappear.
To use the VCR while it is in timer recording standby
mode
Press TIMER to cancel the timer recording standby
mode, then press POWER to turn on the VCR.
DO NOT forget to put the VCR into timer recording
standby mode again by pressing TIMER after you use the
VCR; otherwise, you cannot record the broadcast you
want.
● When “AUTO TIMER” (੬ pg. 57) is set to “ON”, the
timer recording standby mode is automatically
engaged when the VCR is turned off. It is temporarily
canceled when the VCR is turned on. You do not have
to press TIMER to engage or disengage the timer
recording standby mode.
ATTENTION FOR DBS RECEIVER USERS
If you are using a DBS
receiver (unless “DBS
RECEIVER SET” is set to
“OFF” ੬ pg. 21), the band
indication (TV, CATV or
DBS) appears under the
channel number
indication.
TV : To timer-record a regular TV broadcast
received on the VCR.
CATV : To timer-record a cable TV broadcast
received on the VCR, or through a cable
box (unless “CABLE BOX SET” is set to
“OFF” ੬ pg. 18).
DBS : To timer-record a satellite broadcast
received through a DBS receiver.
NOTE:
If “BAND” is set to “TV” on the Tuner Set screen (
੬
pg.
13) and “CABLE BOX SET” is set to “OFF” on the Cable
Box Set screen (
੬
pg. 18), “CATV” will not be displayed
on the Program screen; If “BAND” is set to “CATV” or
“CABLE BOX SET” is set to “ON”, “TV” will not be
displayed.
If the channel number entered requires that the band
be set, “7=DBS” is displayed on the screen.
If this happens, press the Number key “7 (DBS)” to
select “DBS”.
PROGRAM 1
START STOP
8:00AM = 9:00PM
DATE CH
12/24/00 110 SP
SUN DBS
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY, 7=DBS), THEN (0K)
PRESS (PROG.) TO END
NOTES:
●
Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and
other menu settings are lost if it lasts for more than 3 minutes.
As a result, when the power is supplied again to this VCR
after the power failure, the following will take place.
1. This VCR starts the Plug & Play setting automatically to
restore the clock time and channel setting.
2. If the clock time and channel setting are restored correctly,
each timer program you have made will start at its start
time unless its end time has elapsed.
●
Programs that start after midnight must have the next day’s
date.
●
After timer recording is completed, the VCR turns off
automatically.
●
You can program the timer recording while a regular
recording is in progress; the menu screens will not be
recorded.
●
To timer-record cable or satellite channels, be sure to keep
the cable box or DBS receiver turned on.
●
If “MEMORY FULL” appears on the display when you finish a
program setting, the VCR’s memory for the Video Navigation
function is full (
੬
pg. 46). This is not related to actual
recording, so you can finish recording normally, but the Video
Navigation information such as recording date, start time, end
time, and channel number will not be stored in memory.