Marantz DV7110 DVD Player User Manual


 
15
MAKING CONNECTIONS / SETTING UP THE PLAYER
ENGLISH
Setting Up the
Player
Using the Setup Navigator
The Setup Navigator has been designed to simplify the
process of getting the DVD player ready to perform.
Designed as a series of on-screen multiple-choice questions,
the Setup Navigator automatically sets the audio, video, and
language settings according to how the questions are
answered. Once this procedure is complete, it will be
possible to begin using the DVD player to enjoy DVDs.
The procedure on this page describes the operations
necessary to function within the Setup Navigator screens. A
detailed description of the contents of each question that
appears on the screen can be found on the following pages.
When setting up for the first time
Some DVDs start playing automatically when loaded in the
player. Because the Setup Navigator cannot be used if a disc
is playing, it is recommended to set up the player using the
Setup Navigator before loading a DVD for the first time. If a
DVD has been loaded, be sure to press STOP
77
77
7 before
proceeding.
DIMMER
ENTER
RETURN
T-C
+10
RANDOMREPEAT
MENU
TOP
MENU
AUDIO
SUBTITLE
ANGLE
OSDPROGRAM
SETUP
LAST
MEMORY
CONDITION
MEMORY
CLEAR
0
987
654
321
A-B
OPEN/CLOSE
REMOTE CONTROLLER
RC7010DV
VIDEO ON/OFF
3
2
4
1
DIMMER
OSD
VIDEO OFF
FL OFF
PAUSE
STANDBY
LEVEL
REPEAT
PHONES
DVD PLAYER DV7110
STOP
POWER
ON/OFF
OPEN/CLOSE
PLAY
-+
VIDEO
1
DIGITAL OUT
CHAPTER
TITLE
TRACK
TRACK
TIME
TOTAL
FTS
SVCD
CHAPTER
TRACK
SCAN
PBC
A-B
TITLE
REPEAT
DTS
SHUFFLE
1
ENGLISH
TV SYSTEM switch
(except for USA model)
Video output changes as follows according to the playback
disc’s recorded format.
NTSC PAL, PAL NTSC conversion is possible on Video
CDs. PAL NTSC conversion is not possible on DVDs. When
the TV SYSTEM switch is set to the AUTO position, the disc’s
format will be output as is. When a CD or disc is not loaded,
the previous video output format will be selected.
About MOD. (Modulation) PAL
SHRINK
Most models of the newly developed countdown PAL TV
system detect 50 Hz (PAL)/60 Hz (NTSC) and automatically
switch vertical amplitude, resulting in a display without
vertical shrinkage.
If your PAL TV does not have a V Hold control, you may not
be able to view NTSC disc because the picture may roll. If
the TV has a V-Hold control, adjust it until the picture stops
rolling. On some TVs, the picture may shrink vertically,
leaving black bands at the top and bottom of the screen.
This is not a malfunction; it is caused by the NTSC PAL
conversion.
Type
DVD
Video CD
CD, No disc
Format
NTSC
PAL
NTSC
PAL
Disc Output format
Position of TV SYSTEM switch
NTSC PAL AUTO
NTSC MOD. PAL NTSC
PAL PAL
NTSC MOD. PAL NTSC
NTSC PAL PAL
NTSC PAL NTSC or PAL
SYSTEM
TV
PAL
NTSCAUTO
OUTPUT
VIDEO
DVD 2DVD 1
CODE
CONTROL
REMOTE
IN
OUT
S2
VIDEO
21
COAXIAL
EXTERNAL
VIDEO/S2
INTERNAL
2R
L1
CONTROL
REMOTE
OPTICAL
OUTPUT
AUDIO
COMPONENT
OUTPUT
VIDEO
OUTPUT
DIGITAL
COMPONENT
RS-232C
RS-232C CONTROL
RC-5/6RS-232C
Y
CR
/PR
CB
/PB
RS-232C CONTROL
RC-5/6 RS-232C
RS-232C
RS-232C
RS-232C Control Connection
This player can be controlled by a PC. Connect the player
and a serial port on the PC with a 9-pin RS-232C straight
cable. See RS-232C System Control Section (Page 51) for
detail.
RS-232C switch
To control this DVD player by a PC, set the RS-232C switch
on the rear panel to RS-232C.