Mitsumi electronic WD-73734 Flat Panel Television User Manual


  Open as PDF
of 84
 
3. TV Connections 23
Older Cable Box
Required:Onecoaxialcable
Note: Thisconnectionisnotrecommended.The
otherconnectionsdescribedinthischapter
providebetterqualityaudioandvideototheTV
andallowNetCommandtoworkwiththecable
box.
1. Connecttheincomingcableto
IN
oncablebox.
2. Connectonecoaxialcablefrom
OUT
onthecable
boxto
ANT 1/MAIN
ontheTVbackpanel.
INPUT 1
INPUT 2
L
(
MONO) R
AUDIO
DIGITAL
AUDIO
OUT
HDMI
1
2
Y
Pb
Pr
AV R
AUDIO
OUTPUT
S-VIDEO
VIDEO
3
L (MO NO) - A UDIO - R
Y Pb Pr
(480i/480p/720p/1080i )
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM ST EREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720 p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
ANT 1 / MAIN
065
*/


$BCMF#PY
*ODPNJOH
$BCMF
5P"/5."*/
57#BDL1BOFM
Figure 12. Connecting an older cable box
A/V Receiver (Sound System)
Mostsetupsrequireeitheradigitalaudiocableor
analogstereoaudiocables.
TheTVmakesallaudioavailableindigitalandanalog
formats:
AnalogaudiocomingintotheTVisavailableas
outputindigitalformatonthe
DIGITAL AUDIO
OUT
jack.
Digitalincomingaudioisavailableasanalog
outputonthe
AVR AUDIO OUTPUT
/
AUDIO L
(MONO)
and
AUDIO R
jacks.
Usually,onlyoneofthefollowingconnectionsis
required:
• ToconnectananalogA/Vreceiver
Connectleft(white)andright(red)audiocables
from
AVR AUDIO OUTPUT
/
AUDIO L (MONO)
and
AUDIO R
ontheTVbackpaneltothe
TV AUDIO
INPUT
ontheA/Vreceiver.
• ToconnectadigitalA/VreceiverwithDolby
Digital surround sound and PCM audio support:
Connectoneendofthedigitalaudiocable
to
DIGITAL AUDIO OUT
onthebackoftheTV.
Connecttheotherendtothe
COAXIAL DIGITAL
INPUT
onthebackoftheA/Vreceiver.
INPUT 1
INPUT 2
L
(MONO) R
AUDIO
DIGITAL
AUDIO
OUT
HDMI
1
2
Y
Pb
Pr
AVR
AUDIO
OUTPUT
S-VIDEO
VIDEO
3
L (MONO) - AUDIO - R
Y Pb Pr (480i/480p/720p/1080i)
VIDEO: 480i /480p /720p /1080i /1080p
AUDIO: PCM STEREO
PC: VGA / W-VGA / SVGA / W-SVGA /
XGA / W-XGA / SXGA / 720p /1080p
IR EMITTER
NetCommand
R
PC/DVI
AUDIO
INPUT
ANT 2 / AUX
ANT 1 / MAIN
DIGITAL
AUDIO
OUT
AVR
AUDIO
OUTPUT
%JHJUBM$PBYJBM$BCMF
6TFUPDPOOFDUB
EJHJUBM"7SFDFJWFS
4UFSFP"OBMPH$BCMFT
6TFUPDPOOFDUBO
BOBMPH"7SFDFJWFS
Figure 11. Connecting the TV to an A/V receiver
Important
A/V Receivers with HDMI Inputs
If your A/V receiver has an HDMI input, use
one of the audio connections described here
instead of an HDMI connection.
Note:
Onrareoccasions,anHDMIsignalmaybe
copy-restrictedandcannotbeoutputfrom
theTVasadigitalsignal.Tohearthesecopy-
protectedsignalsthroughtheA/Vreceiver,use
connectionsforanalogA/Vreceivers.
ChecktheA/Vreceiver’sOwner’sGuidefor
informationconcerninguseofthedigitalinput
andswitchingbetweendigitalsoundand
analogstereosoundfromtheTV.
 previous next